Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Blower Motor Circuit  


DESCRIPTION

The blower motor with fan sub-assembly is operated by signals from the air conditioning amplifier assembly. Blower motor speed signals are transmitted in accordance with changes in the duty ratio.

WIRING DIAGRAM

E332464E11
2.125,0.521 2.49,0.802 0.365,0.281 10 false 3 2.115,0.927 2.479,1.208 0.365,0.281 10 false 2 2.125,1.302 2.49,1.583 0.365,0.281 10 false 1 1.854,0.625 2.219,0.906 0.365,0.281 10 false +B 1.875,1.021 2.24,1.302 0.365,0.281 10 false SI 1.76,1.427 2.125,1.708 0.365,0.281 10 false GND 0.375,2.01 0.74,2.292 0.365,0.281 10 false F7 0.375,2.156 2.688,2.438 2.313,0.281 10 false Blower Motor with Fan Sub-assembly 4.677,1.875 5.042,2.156 0.365,0.281 10 false F73 4.667,2.021 7.063,2.313 2.396,0.292 10 false Air Conditioning Amplifier Assembly 4.958,1.313 5.323,1.594 0.365,0.281 10 false 4 4.948,0.917 5.313,1.198 0.365,0.281 10 false 6 5.115,0.917 5.719,1.156 0.604,0.24 10 false BLW 5.125,1.417 5.688,1.677 0.563,0.26 10 false GND 2.656,0.771 3.021,1.052 0.365,0.281 10 false HTR 3.698,0.594 5.229,0.896 1.531,0.302 10 false from Auxiliary Battery 6.135,0.99 6.74,1.229 0.604,0.24 10 false IC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Blower Motor Blower motor with fan sub-assembly Min.: 0, Max.: 31 -
Body Electrical > Air Conditioner > Active Test
Tester Display
Blower Motor
50004 121 2

Result:
Result Proceed to
OK A
NG (Blower motor with fan sub-assembly does not operate) B
NG (Blower motor with fan sub-assembly operates but does not change speed) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)

C

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the F7 blower motor with fan sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - AUXILIARY BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F7-3 (+B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BLOWER MOTOR WITH FAN SUB-ASSEMBLY)
a.

Disconnect the F73 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F73-6 (BLW) - F7-2 (SI) Always Below 1 Ω
F73-6 (BLW) or F7-2 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY
a.

Reconnect the F7 blower motor with fan sub-assembly connector.


b.
E328994C08
1.479,0.448 1.844,0.708 0.365,0.26 1.229,2.958 0.938,2.26 true 0.042,0.125 0.354,0.281 0.313,0.156 10 false *a 1.552,0.49 2.104,0.938 0.552,0.448 10 false F73 1.25,2.99 1.646,3.156 0.396,0.167 10 false BLW
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F73-6 (BLW) - Body ground Always 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

6.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Reconnect the F73 air conditioning amplifier assembly connector.


b.

Turn the power switch on (IG).


c.

Turn the blower switch on (LO).


d.
E328995C07
1.75,0.375 2.146,0.604 0.396,0.229 2.573,2.083 2.406,1.406 true 1.146,2.115 1.552,1.302 true 0.167,0.135 0.479,0.292 0.313,0.156 10 false *a 1.833,0.406 2.115,0.604 0.281,0.198 10 false F73 1,2.146 1.49,2.344 0.49,0.198 10 false GND 2.427,2.146 2.885,2.406 0.458,0.26 10 false BLW 2.813,3.74 3.271,3.938 0.458,0.198 10 false GND
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Connect an oscilloscope to terminals F73-6 (BLW) and F73-4 (GND) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


HINT:

The waveform varies with the blower speed.


Item Content
Tool Setting 2 V/DIV., 1 ms./DIV.
Vehicle Condition
·

Power switch on (IG)

·

Blower switch: LO




Result:
Proceed to
OK
NG



OK

REPLACE BLOWER MOTOR WITH FAN SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY