Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300711 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system. This sensor is connected to the air conditioning amplifier assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the thermistor assembly and reads voltage changes due to changes in the resistance of the thermistor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412 Ambient Temperature Sensor Circuit
Any of the following conditions is met:
·

Open in ambient temperature sensor circuit

·

Short in ambient temperature sensor circuit


·

Thermistor assembly

·

Harness or connector between thermistor assembly and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approximately -52.9°C (-63.22°F) or lower, DTC B1412 may be output even though the system is normal.


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on ambient temperature (IG) ○ ○
Malfunction Status Open in ambient temperature sensor circuit ○ -
Short in ambient temperature sensor circuit - ○
Detection Time 4 seconds or more 4 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E332457E21
4.573,0.688 4.833,0.948 0.26,0.26 10 false 13 2.135,0.688 2.396,0.948 0.26,0.26 10 false 1 2.135,1.167 2.396,1.427 0.26,0.26 10 false 2 0.615,1.781 0.948,2.052 0.333,0.271 10 false A3 0.615,1.938 2.292,2.354 1.677,0.417 10 false Thermistor Assembly 4.583,1.792 5.323,2.146 0.74,0.354 10 false F71 4.594,1.938 6.969,2.323 2.375,0.385 10 false Air Conditioning Amplifier Assembly 4.802,1.177 5.24,1.49 0.438,0.313 10 false SG-2 4.802,0.698 5.219,0.948 0.417,0.25 10 false TAM 4.646,1.177 4.906,1.438 0.26,0.26 10 false 2 5.688,0.281 6.104,0.531 0.417,0.25 10 false 5 V 6.271,0.75 6.688,1 0.417,0.25 10 false AD

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT THERMISTOR ASSEMBLY

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

4.CHECK FOR DTC
2.INSPECT THERMISTOR ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F71 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-13 (TAM) - A3-1 Always Below 1 Ω
F71-2 (SG-2) - A3-2 Always Below 1 Ω
F71-13 (TAM) or A3-1 - Body ground Always 10 kΩ or higher
F71-2 (SG-2) or A3-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY