Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM32K0E _59 Vehicle Exterior _061311 WINDOW / GLASS _0301222 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B150964C11
2.708,0.083 3.208,0.333 0.5,0.25 3.813,0.083 4.313,0.333 0.5,0.25 2.896,0.115 3.188,0.313 0.292,0.198 10 false J6 4.031,0.115 4.323,0.313 0.292,0.198 10 false I6 3.25,0.115 3.563,0.333 0.313,0.219 10 false *A 4.344,0.115 4.656,0.333 0.313,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J6*1 or I6*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-11 (B) - J6-12 (GND) B - W-B Power supply Power switch off 11 to 14 V
J6-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I6-11 (B) - I6-12 (GND) B - W-B Power supply Power switch off 11 to 14 V
I6-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J6*1 or I6*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J6-15 (DOWN) - J6-12 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J6-15 (DOWN) - J6-12 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J6-20 (UP) - J6-12 (GND) V - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
J6-20 (UP) - J6-12 (GND) V - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I6-15 (DOWN) - I6-12 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
I6-15 (DOWN) - I6-12 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
I6- 20 (UP) - I6-12 (GND) V - W-B Power window motor UP output Power switch on (IG), driver door power window regulator switch not pushed or pulled 11 to 14 V
I6-20 (UP) - I6-12 (GND) V - W-B Power window motor UP output Power switch on (IG), driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR SWITCH ASSEMBLY


B462696C01
2.823,0.115 3.24,0.365 0.417,0.25 3.844,0.125 4.25,0.375 0.406,0.25 2.948,0.156 3.406,0.354 0.458,0.198 10 false I10 3.323,0.156 3.635,0.354 0.313,0.198 10 false *A 3.969,0.146 4.281,0.344 0.313,0.198 10 false J8 4.313,0.156 4.625,0.354 0.313,0.198 10 false *B
*A for LHD *B for RHD


a.

Disconnect the I10*1 or J8*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I10-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J8-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the I10*1 or J8*2 power window regulator switch assembly connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I10-2 (LED) - I10-7 (GND) R - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
I10-2 (LED) - I10-7 (GND) R - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
I10-5 (UP) - I10-7 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
I10-5 (UP) - I10-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
I10-5 (UP) - I10-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
I10-5 (UP) - I10-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
I10-5 (UP) - I10-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I10-4 (DOWN) - I10-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
I10-4 (DOWN) - I10-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
I10-4 (DOWN) - I10-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I10-4 (DOWN) - I10-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
I10-4 (DOWN) - I10-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
I10-8 (AUTO) - I10-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J8-2 (LED) - J8-7 (GND) R - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
J8-2 (LED) - J8-7 (GND) R - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
J8-5 (UP) - J8-7 (GND) V - W-B Power window motor UP output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
J8-5 (UP) - J8-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J8-5 (UP) - J8-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
J8-5 (UP) - J8-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J8-5 (UP) - J8-7 (GND) V - W-B Power window motor UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J8-4 (DOWN) - J8-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
J8-4 (DOWN) - J8-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J8-4 (DOWN) - J8-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J8-4 (DOWN) - J8-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J8-4 (DOWN) - J8-7 (GND) Y - W-B Power window motor DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully open 11 to 14 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO UP output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J8-8 (AUTO) - J8-7 (GND) B - W-B Power window motor AUTO DOWN output Power switch on (IG), front passenger door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


B462696N01
3.365,0.115 3.781,0.375 0.417,0.26 3.51,0.177 3.823,0.375 0.313,0.198 10 false L3

a.

Disconnect the L3 rear power window regulator switch assembly (for LH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L3-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the L3 rear power window regulator switch assembly (for LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L3-2 (LED) - L3-7 (GND) Y - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
L3-2 (LED) - L3-7 (GND) Y - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
L3-5 (UP) - L3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
L3-5 (UP) - L3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
L3-5 (UP) - L3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
L3-5 (UP) - L3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
L3-5 (UP) - L3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L3-4 (DOWN) - L3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
L3-4 (DOWN) - L3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
L3-4 (DOWN) - L3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L3-4 (DOWN) - L3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
L3-4 (DOWN) - L3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully open 11 to 14 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
L3-8 (AUTO) - L3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear LH door power window fully open 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR RH DOOR)


B462696N02
3.375,0.104 3.792,0.365 0.417,0.26 3.5,0.167 3.833,0.375 0.333,0.208 10 false K3

a.

Disconnect the K3 rear power window regulator switch assembly (for RH door) connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K3-7 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K3 rear power window regulator switch assembly (for RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K3-2 (LED) - K3-7 (GND) Y - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
K3-2 (LED) - K3-7 (GND) Y - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
K3-5 (UP) - K3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
K3-5 (UP) - K3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
K3-5 (UP) - K3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
K3-5 (UP) - K3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K3-5 (UP) - K3-7 (GND) W - W-B Power window motor UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K3-4 (DOWN) - K3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
K3-4 (DOWN) - K3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
K3-4 (DOWN) - K3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K3-4 (DOWN) - K3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K3-4 (DOWN) - K3-7 (GND) GR - W-B Power window motor DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully open 11 to 14 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO UP output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K3-8 (AUTO) - K3-7 (GND) V - W-B Power window motor AUTO DOWN output Power switch on (IG), rear RH door power window fully open 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)


B280976C24
2.115,0.604 2.51,0.844 0.396,0.24 2.115,0.938 2.51,1.177 0.396,0.24 2.24,0.625 2.563,0.844 0.323,0.219 10 false J2 2.271,0.958 2.594,1.177 0.323,0.219 10 false I2 2.542,0.625 2.865,0.844 0.323,0.219 10 false *A 2.542,0.958 2.865,1.177 0.323,0.219 10 false *B
*A for LHD *B for RHD


a.

Disconnect the J2*1 or I2*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J2-2 (B) - Body ground L - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I2-2 (B) - Body ground L - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the J2*1 or I2*2 power window regulator motor assembly (for driver door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully closed 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), driver door power window fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) not pushed or pulled 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), multiplex network master switch assembly (driver door power window regulator switch) fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window moving, multiplex network master switch assembly (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), driver door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)


B280976C25
2.104,0.625 2.5,0.865 0.396,0.24 2.104,0.948 2.5,1.188 0.396,0.24 2.26,0.667 2.677,0.875 0.417,0.208 10 false I2 2.229,0.979 2.646,1.188 0.417,0.208 10 false J2 2.542,0.979 2.958,1.188 0.417,0.208 10 false *B 2.542,0.667 2.958,0.875 0.417,0.208 10 false *A
*A for LHD *B for RHD


a.

Disconnect the I2*1 or J2*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
I2-2 (B) - Body ground L - Body ground Power supply Power switch off 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
J2-2 (B) - Body ground L - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the I2*1 or J2*2 power window regulator motor assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Measure the voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
I2-4 (AUTO) - I2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
I2-5 (LED) - I2-1 (GND) R - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
I2-5 (LED) - I2-1 (GND) R - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
I2-7 (DOWN) - I2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
I2-10 (UP) - I2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J2-4 (AUTO) - J2-1 (GND) B - W-B Power window motor AUTO DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
J2-5 (LED) - J2-1 (GND) R - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
J2-5 (LED) - J2-1 (GND) R - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully closed 11 to 14 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
J2-7 (DOWN) - J2-1 (GND) Y - W-B Power window motor DOWN input Power switch on (IG), front passenger door power window fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), power window regulator switch assembly not pushed or pulled 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully open 11 to 14 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
J2-10 (UP) - J2-1 (GND) V - W-B Power window motor UP input Power switch on (IG), front passenger door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)


B286758N17
2.292,0.771 2.656,0.99 0.365,0.219 2.406,0.792 2.792,1 0.385,0.208 10 false L2

a.

Disconnect the L2 power window regulator motor assembly (for rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L2-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the L2 power window regulator motor assembly (for rear LH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
L2-4 (AUTO) - L2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
L2-5 (LED) - L2-1 (GND) Y - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
L2-5 (LED) - L2-1 (GND) Y - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
L2-7 (DOWN) - L2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
L2-7 (DOWN) - L2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pushed halfway down (Manual operation) Below 1 V
L2-7 (DOWN) - L2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully closed 11 to 14 V
L2-7 (DOWN) - L2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pushed down (Auto operation) Below 1 V
L2-7 (DOWN) - L2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear LH door power window fully open 11 to 14 V
L2-10 (UP) - L2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for LH door) not pushed or pulled 11 to 14 V
L2-10 (UP) - L2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) pulled halfway up (Manual operation) Below 1 V
L2-10 (UP) - L2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully open 11 to 14 V
L2-10 (UP) - L2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear LH door power window moving, rear power window regulator switch assembly (for LH door) fully pulled up (Auto operation) Below 1 V
L2-10 (UP) - L2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear LH door power window fully closed 11 to 14 V



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR)


B280976N60
2.219,0.771 2.615,1.01 0.396,0.24 2.333,0.802 2.646,1.042 0.313,0.24 10 false K2

a.

Disconnect the K2 power window regulator motor assembly (for rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K2-2 (B) - Body ground R - Body ground Power supply Power switch off 11 to 14 V


c.

Reconnect the K2 power window regulator motor assembly (for rear RH door) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K2-4 (AUTO) - K2-1 (GND) V - W-B Power window motor AUTO DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
K2-5 (LED) - K2-1 (GND) Y - W-B LED illumination signal Headlight dimmer switch is in the tail position 11 to 14 V
K2-5 (LED) - K2-1 (GND) Y - W-B LED illumination signal Headlight dimmer switch is not in the tail position Below 1 V
K2-7 (DOWN) - K2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
K2-7 (DOWN) - K2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pushed halfway down (Manual operation) Below 1 V
K2-7 (DOWN) - K2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully closed 11 to 14 V
K2-7 (DOWN) - K2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pushed down (Auto operation) Below 1 V
K2-7 (DOWN) - K2-1 (GND) GR - W-B Power window motor DOWN input Power switch on (IG), rear RH door power window fully open 11 to 14 V
K2-10 (UP) - K2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear power window regulator switch assembly (for RH door) not pushed or pulled 11 to 14 V
K2-10 (UP) - K2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) pulled halfway up (Manual operation) Below 1 V
K2-10 (UP) - K2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully open 11 to 14 V
K2-10 (UP) - K2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear RH door power window moving, rear power window regulator switch assembly (for RH door) fully pulled up (Auto operation) Below 1 V
K2-10 (UP) - K2-1 (GND) W - W-B Power window motor UP input Power switch on (IG), rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B434105C28
2.146,3.104 2.542,3.344 0.396,0.24 4.604,3.083 5,3.323 0.396,0.24 1.396,4.573 1.792,4.813 0.396,0.24 3.729,4.583 4.125,4.823 0.396,0.24 5.292,4.615 5.688,4.854 0.396,0.24 6.292,4.625 6.688,4.865 0.396,0.24 4.646,6.229 5.042,6.469 0.396,0.24 1.51,6.208 1.906,6.448 0.396,0.24 3.417,7.844 3.813,8.083 0.396,0.24 1.667,1.479 1.906,1.479 false 4.031,0.813 4.031,0.24 4.031,0.24 4.146,0.24 false 1.667,1.802 1.906,1.802 false 1.604,0.646 1.604,0.302 1.604,0.302 1.719,0.302 false 1.438,2.792 1.438,1.469 1.438,1.469 1.552,1.469 false 1.438,1.802 1.552,1.802 false 1.969,1.427 2.281,1.625 0.313,0.198 10 false F15 4.229,0.167 4.542,0.365 0.313,0.198 10 false MB 0.875,1.115 1.188,1.313 0.313,0.198 10 false 3H 0.885,1.656 1.198,1.854 0.313,0.198 10 false 3F 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3L 0.896,2.25 1.208,2.448 0.313,0.198 10 false 3K 1.969,1.74 2.281,1.938 0.313,0.198 10 false F16 5.854,1.135 6.167,1.333 0.313,0.198 10 false 3D 5.854,1.781 6.167,1.979 0.313,0.198 10 false 3A 4.698,3.125 5.01,3.323 0.313,0.198 10 false F15 2.219,3.146 2.531,3.344 0.313,0.198 10 false F16 1.521,4.615 1.833,4.813 0.313,0.198 10 false 3H 3.865,4.625 4.177,4.823 0.313,0.198 10 false 3F 5.417,4.667 5.729,4.865 0.313,0.198 10 false 3L 6.406,4.677 6.719,4.875 0.313,0.198 10 false 3K 1.625,6.26 1.938,6.458 0.313,0.198 10 false 3D 4.771,6.281 5.083,6.479 0.313,0.198 10 false 3A 3.531,7.896 3.844,8.094 0.313,0.198 10 false MB 0.115,0.333 1.021,0.531 0.906,0.198 12 false *A 1.771,0.25 2.677,0.448 0.906,0.198 10 false *1 1.365,2.833 2.271,3.031 0.906,0.198 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B434104C33
3.531,3.198 3.896,3.417 0.365,0.219 1.396,4.583 1.76,4.802 0.365,0.219 3.729,4.583 4.094,4.802 0.365,0.219 5.313,4.583 5.677,4.802 0.365,0.219 6.302,4.552 6.667,4.771 0.365,0.219 1.583,6.24 1.948,6.458 0.365,0.219 4.813,6.26 5.177,6.479 0.365,0.219 3.354,7.854 3.719,8.073 0.365,0.219 1.667,1.333 1.906,1.333 false 4,0.813 4,0.365 4,0.365 4.125,0.365 false 1.625,0.656 1.625,0.281 1.625,0.281 1.75,0.281 false 1.417,2.708 1.417,1.333 1.417,1.333 1.542,1.333 false 0.865,1.094 1.177,1.292 0.313,0.198 10 false 3H 0.865,1.646 1.177,1.844 0.313,0.198 10 false 3F 0.875,2.01 1.188,2.208 0.313,0.198 10 false 3L 0.885,2.24 1.198,2.438 0.313,0.198 10 false 3K 1.969,1.26 2.281,1.458 0.313,0.198 10 false F15 4.188,0.292 4.5,0.49 0.313,0.198 10 false MB 5.844,1.104 6.156,1.302 0.313,0.198 10 false 3D 5.844,1.76 6.156,1.958 0.313,0.198 10 false 3A 3.635,3.219 3.948,3.417 0.313,0.198 10 false F15 1.5,4.604 1.813,4.802 0.313,0.198 10 false 3H 3.823,4.604 4.135,4.802 0.313,0.198 10 false 3F 5.427,4.604 5.74,4.802 0.313,0.198 10 false 3L 6.396,4.583 6.708,4.781 0.313,0.198 10 false 3K 1.688,6.26 2,6.458 0.313,0.198 10 false 3D 4.917,6.292 5.229,6.49 0.313,0.198 10 false 3A 3.438,7.875 3.75,8.073 0.313,0.198 10 false MB 0.167,0.115 1.354,0.49 1.188,0.375 12 false *A 1.833,0.229 3.021,0.604 1.188,0.375 10 false *1 1.344,2.75 2.531,3.125 1.188,0.375 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 1 Connector - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors connected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-31 (BECU) - Body ground - Battery power supply Power switch off 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-32 (IG) - Body ground - IG power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - IG power supply Power switch off Below 1 V


d.

Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.

Click here



e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F15-6 (FLCY) - Body ground R - Body ground Front door courtesy light switch (for LH) input Front door LH open Below 1 V
F15-6 (FLCY) - Body ground R - Body ground Front door courtesy light switch (for LH) input Front door LH closed 11 to 14 V
F15-27 (FRCY) - Body ground BR - Body ground Front door courtesy light switch (for RH) input Front door RH open Below 1 V
F15-27 (FRCY) - Body ground BR - Body ground Front door courtesy light switch (for RH) input Front door RH closed 11 to 14 V
F15-29 (L2) - Body ground G - Body ground Driver door key-linked lock input Driver door key cylinder turned to lock Below 1 V
F15-29 (L2) - Body ground G - Body ground Driver door key-linked lock input Driver door key cylinder not turned Pulse generation
F15-2 (UL3) - Body ground L - Body ground Driver door key-linked unlock input Driver door key cylinder turned to unlock Below 1 V
F15-2 (UL3) - Body ground L - Body ground Driver door key-linked unlock input Driver door key cylinder not turned Pulse generation