When the windshield deicer switch on the air conditioning control assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly. via LIN communication. When the air conditioning amplifier assembly receives the signal, it turns on the DEICER relay to operate the windshield deicer system.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the auxiliary battery voltage becomes low, windshield deicer operation is canceled to prioritize supplying power to the power steering system.
Check air conditioning system.
Both the windshield deicer system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly via the same communication line.
The air conditioning system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform the Active Test.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Deicer Relay (Front) | Windshield glass (windshield deicer) | OFF or ON | - |
| Tester Display |
|---|
| Deicer Relay (Front) |
The windshield deicer system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace sir conditioning control assembly with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL
Check that the window defogger system operates normally.
Click hereVehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>OPERATION CHECK
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Disconnect the 3F and 3A instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3F-5 - Body ground | Power switch off | 11 to 14 V |
| 3A-21 - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3A instrument panel junction block assembly connector.
Disconnect the F73 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-18 - F73-17 (FDEF) | Always | Below 1 Ω |
| 3A-18 or F73-17 (FDEF) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
| *a | Component without harness connected (Instrument Panel Junction Block) | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-5 - 3F-4 | Auxiliary battery voltage applied between terminals 3A-21 and 3A-18 | Below 1 Ω |
| Auxiliary battery voltage not applied between terminals 3A-21 and 3A-18 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A64 windshield glass (windshield deicer) connector.
Disconnect the 3F instrument panel junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3F-4 - A64-1(B) | Always | Below 1 Ω |
| 3F-4 or A64-1(B) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Windshield Glass [Windshield Deicer]) |
Disconnect the windshield glass (windshield deicer) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG