The radio receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio receiver assembly.
Disconnect the F47 radio receiver assembly connector.
Disconnect the R2 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-6 (SNS2) - R2-1 (SNS2) | Always | Below 1 Ω |
| F47-4 (MACC) - R2-9 (MACC) | Always | Below 1 Ω |
| F47-5 (MIN+) - R2-8 (MCO+) | Always | Below 1 Ω |
| F47-19 (MIN-) - R2-7 (MCO-) | Always | Below 1 Ω |
| F47-6 (SNS2) or R2-1 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F47-4 (MACC) or R2-9 (MACC) - Body ground | Always | 10 kΩ or higher |
| F47-5 (MIN+) or R2-8 (MCO+) - Body ground | Always | 10 kΩ or higher |
| F47-19 (MIN-) or R2-7 (MCO-) - Body ground | Always | 10 kΩ or higher |
| F47-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F47 radio receiver assembly connector.
Connect the R2 map light assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Radio Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-4 (MACC) - Body ground | power switch on (ACC). | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F47-18 (SGND) - Body ground | Always | Below 1 Ω |
| F47-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the R2 map light assembly (telephone microphone assembly) connector.
Turn the power switch on (ACC).
| *a | Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. | B |
A
B