The main body ECU (multiplex network body ECU) receives switch signals from the multiplex network master switch assembly and driver door key cylinder lock or unlock switch signals from the front door lock with motor assembly RH*1 or front door lock with motor assembly LH*2. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
*1: for RHD
*2: for LHD
for LHD
for RHD
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The power door lock control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power door lock control system after confirming that the communication systems are functioning properly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check door lock operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| All doors cannot be locked by multiplex network master switch assembly | A |
| All doors cannot be locked by driver door key cylinder | B |
A
B
Clear the DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs.
DTC B1206 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the multiplex network master switch assembly.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check that all doors can be locked and unlocked by the multiplex network master switch assembly.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
All doors can be locked and unlocked by the multiplex network master switch assembly.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Key SW-Lock | Driver door key-linked lock / unlock switch lock signal | OFF or ON | OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position |
- |
| D Door Key SW-UL | Driver door key-linked lock / unlock switch unlock signal | OFF or ON | OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position |
- |
| Tester Display |
|---|
| Door Key SW-Lock |
| D Door Key SW-UL |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
for LHD
Remove the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for RHD
Remove the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Disconnect the J4 front door lock with motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J4-9 (L) - F15-29 (L2) | Always | Below 1 Ω |
| J4-10 (UL) - F15-2 (UL3) | Always | Below 1 Ω |
| J4-7 (E) - Body ground | Always | Below 1 Ω |
| J4-9 (L) or F15-29 (L2) - Body ground | Always | 10 kΩ or higher |
| J4-10 (UL) or F15-2 (UL3) - Body ground | Always | 10 kΩ or higher |
for RHD
Disconnect the F15 main body ECU (multiplex network body ECU) connector.
Disconnect the I4 front door lock with motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-6 (L) - F15-29 (L2) | Always | Below 1 Ω |
| I4-5 (UL) - F15-2 (UL3) | Always | Below 1 Ω |
| I4-8 (E) - Body ground | Always | Below 1 Ω |
| I4-6 (L) or F15-29 (L2) - Body ground | Always | 10 kΩ or higher |
| I4-5 (UL) or F15-2 (UL3) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C