Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061818 DOOR LOCK _0301275 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The electrical key and TPMS receiver assemblyis used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the electrical key and TPMS receiver assembly. The electrical key and TPMS receiver assemblyreceives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). (ex. If a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short to ground in RDAM terminal circuit between the certification ECU (smart key ECU assembly) and electrical key and TPMS receiver assembly.

·

Short to ground in RDAM terminal circuit when voltage (5 V) is not being output from terminal RCO


·

Wire harness or connector

·

Electrical key and TPMS receiver assembly

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

E358344E04
1.885,0.833 2.198,1.031 0.313,0.198 10 false +5 1.677,1.521 2.292,1.719 0.615,0.198 10 false DATA 1.75,2.219 2.365,2.417 0.615,0.198 10 false GND 0.896,1.396 1.115,1.625 0.219,0.229 10 false IC 2.167,0.833 2.479,1.031 0.313,0.198 10 false 8 2.167,1.521 2.479,1.719 0.313,0.198 10 false 2 2.146,2.115 2.458,2.313 0.313,0.198 10 false 12 0.625,2.677 1.24,2.875 0.615,0.198 10 false M23 0.604,2.875 2.188,3.448 1.583,0.573 10 false Electrical Key and TPMS Receiver Assembly 5.188,2.833 6.74,3.271 1.552,0.438 10 false Certification ECU (Smart Key ECU Assembly) 5.281,1.521 5.896,1.719 0.615,0.198 10 false RDAM 5.271,0.833 5.885,1.031 0.615,0.198 10 false RCO 5.292,2.208 5.906,2.406 0.615,0.198 10 false E 4.927,0.927 5.229,1.125 0.302,0.198 10 false M67 4.927,1.615 5.229,1.813 0.302,0.198 10 false M67 4.979,2.219 5.281,2.417 0.302,0.198 10 false F1 4.958,0.75 5.271,0.948 0.313,0.198 10 false 18 4.958,1.438 5.271,1.635 0.313,0.198 10 false 19 4.958,2.031 5.271,2.229 0.313,0.198 10 false 18 5.781,0.417 6.115,0.625 0.333,0.208 10 false 5 V 5.792,1.125 6.125,1.333 0.333,0.208 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the electrical key and TPMS receiver assemblyand wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the electrical key and TPMS receiver assembly, the performance of the entry function and wireless function may be affected.

·

This DTC is not stored within 10 seconds of the power switch being turned from on (IG) to off.

·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

When replacing the electrical key and TPMS receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

It is necessary to perform initialization (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the electrical key and TPMS receiver assembly if the electrical key and TPMS receiver assembly has been replaced.



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M23 electrical key and TPMS receiver assembly connector.

B440788C13
3.198,0.396 3.604,0.635 0.406,0.24 4.521,0.427 4.927,0.667 0.406,0.24 4.115,2.583 3.979,2.583 3.979,2.583 3.813,1.448 true 4.896,2.594 4.76,2.594 4.76,2.594 3.906,1.438 true 5.688,2.25 5.552,2.25 5.552,2.25 5.208,1.448 true 3.271,0.438 3.729,0.635 0.458,0.198 10 false M67 4.635,0.469 5.094,0.667 0.458,0.198 10 false F1 4.958,2.51 5.573,2.708 0.615,0.198 10 false RCO 4.177,2.51 4.792,2.708 0.615,0.198 10 false RDAM 5.75,2.177 6.365,2.375 0.615,0.198 10 false E 0.146,0.104 0.604,0.302 0.458,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M67-19 (RDAM) - F1-18 (E) Power switch off 11 to 14 V
M67-18 (RCO) - F1-18 (E) always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals


Standard Resistance:
Tester Connection Condition Specified Condition
F1-18 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY AND TPMS RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TPMS RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY AND TPMS RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F1 and M67 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M67-19 (RDAM) - M23-2 (DATA) Always Below 1 Ω
M67-18 (RCO) - M23-8 (+5) Always Below 1 Ω
M23-12 (GND) - Body ground Always Below 1 Ω
M23-2 (DATA) or M67-19 (RDAM) - Body ground Always 10 kΩ or higher
M23-8 (+5) or M67-18 (RCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR