Wear protective gloves. Sharp areas on the parts may injure your hands.
71075B
1.INSTALL BENCH TYPE REAR SEAT CUSHION COVER
When installing a bench type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION
Engage the claws to install the bench type rear seat cushion cover to the No. 1 rear seat cushion pad sub-assembly.
Be careful not to damage the bench type rear seat cushion cover.
Install the rear seat cushion pad to the No. 1 rear seat cushion pad sub-assembly.
Engage the hooks and hook and loop fastener to install the bench type rear seat cushion cover.
| *a | Hook and Loop Fastener | - | - |
Be careful not to damage the bench type rear seat cushion cover.
73735
2.INSTALL CHILD RESTRAINT SEAT GUIDE CUP (w/ Cover)
Install the child restraint seat guide cup.
Use the same procedure for all child restraint seat guide cups.
73731C
3.INSTALL NO. 2 CHILD RESTRAINT SEAT COVER (w/ Cover)
|
Install in this Direction |
Engage the claws to install the No. 2 child restraint seat cover as shown in the illustration.
Use the same procedure for all No. 2 child restraint seat covers.
73731B
4.INSTALL NO. 1 CHILD RESTRAINT SEAT COVER (w/ Cover)
|
Install in this Direction |
Engage the guides and claws to install the No. 1 child restraint seat cover as shown in the illustration.
Use the same procedure for all No. 1 child restraint seat covers.
72640A
5.INSTALL REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)
Engage the guides to install the rear seatback lock assembly LH.
Install the 2 bolts.
71078S
6.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for LH Side)
When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION
Engage the claws to install the separate type rear seatback cover to the separate type rear seatback pad LH.
Be careful not to damage the separate type rear seatback cover.
7.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for LH Side)
Install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.
71931A
8.INSTALL REAR SEAT HEADREST SUPPORT (for LH Side)
|
Install in this Direction |
Engage the claws to install the 2 rear seat headrest supports as shown in the illustration.
71702C
9.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH (for LH Side)
Engage the guides and claws to install the rear seatback board sub-assembly LH.
| *a | Fastener |
Close the 2 fasteners as shown in the illustration.
Engage the hook.
72679
10.INSTALL REAR SEATBACK LOCK CONTROL BEZEL (for LH Side)
Engage the hooks to the separate type rear seatback cover.
Engage the claws to install a new rear seatback lock control bezel.
72630C
11.INSTALL REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)
Engage the guides to install the rear seatback lock assembly RH.
Install the 2 bolts.
73350C
12.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)
71077S
13.INSTALL SEPARATE TYPE REAR SEATBACK COVER (for RH Side)
When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION
Engage the claws to install the separate type rear seatback cover to the separate type rear seatback pad RH.
Be careful not to damage the separate type rear seatback cover.
14.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD (for RH Side)
Pass the rear center seat outer belt assembly through the separate type rear seatback cover with pad and temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly RH as shown in the illustration.
71931A
15.INSTALL REAR SEAT CENTER HEADREST SUPPORT (w/ Center Headrest)
|
Install in this Direction |
Engage the claws to install the 2 rear seat center headrest supports as shown in the illustration.
71931A
16.INSTALL REAR SEAT HEADREST SUPPORT (for RH Side)
|
Install in this Direction |
Engage the claws to install the 2 rear seat headrest supports as shown in the illustration.
71701C
17.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY RH (for RH Side)
Engage the guides and claws to install the rear seatback board sub-assembly RH.
| *a | Fastener |
Close the 2 fasteners as shown in the illustration.
Engage the hook.
72679
18.INSTALL REAR SEATBACK LOCK CONTROL BEZEL (for RH Side)
Engage the hooks to the separate type rear seatback cover.
Engage the claws to install a new rear seatback lock control bezel.
73373F
19.INSTALL REAR SEAT SHOULDER BELT HOLE COVER (for RH Side)
Install the rear seat shoulder belt hole cover.
73178A
20.INSTALL SEAT BELT ANCHOR COVER CAP (for RH Side)
|
Install in this Direction |
Engage the guides to install the seat belt anchor cover cap as shown in the illustration.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the rear seat shoulder belt cover with seat belt anchor cover cap as shown in the illustration.