Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061817 AUDIO / VIDEO _0301367 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E361248E01
5.146,4.031 6.844,4.417 1.698,0.385 10 false Radio and Display Receiver Assembly 5.281,2.646 5.896,2.844 0.615,0.198 10 false IG 5.26,3.583 5.875,3.781 0.615,0.198 10 false GND1 5.26,1.708 5.875,1.906 0.615,0.198 10 false ACC1 5.281,0.781 5.896,0.979 0.615,0.198 10 false +B1 4.833,3.583 5.448,3.781 0.615,0.198 10 false F126 4.813,1.719 5.427,1.917 0.615,0.198 10 false F126 4.833,0.792 5.448,0.99 0.615,0.198 10 false F126 4.844,2.656 5.458,2.854 0.615,0.198 10 false F125 3.24,2.854 4.323,3.031 1.083,0.177 10 false ECU-IG-NO. 4 3.313,1.896 4.396,2.073 1.083,0.177 10 false ECU-ACC 3.406,0.958 4.49,1.135 1.083,0.177 10 false RADIO 1.302,1.698 2.823,1.906 1.521,0.208 10 false from ACC Relay 0.969,2.635 2.49,2.844 1.521,0.208 10 false from IG1 NO. 1 Relay 1.021,0.792 4.385,0.99 3.365,0.198 10 false from Auxiliary Battery 4.927,0.573 5.083,0.771 0.156,0.198 10 false 4 4.917,1.5 5.073,1.698 0.156,0.198 10 false 3 4.927,2.427 5.083,2.625 0.156,0.198 10 false 1 4.927,3.365 5.083,3.563 0.156,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-7 (GND1) - Body ground Always Below 1 Ω



c.
E360339C01
1.448,0.115 1.906,0.427 0.458,0.313 1.479,1.563 1.938,1.875 0.458,0.313 1.292,1.333 1.563,1.052 true 2.198,0.792 2.531,0.677 true 2,0.698 2.219,0.417 true 0.938,2.552 0.729,3.104 true 1.542,1.625 2.156,1.823 0.615,0.198 10 false F125 1.521,0.188 2.135,0.385 0.615,0.198 10 false F126 0.896,1.313 1.51,1.51 0.615,0.198 10 false GND1 2.583,0.583 3.198,0.781 0.615,0.198 10 false +B1 2.25,0.281 2.865,0.479 0.615,0.198 10 false ACC1 0.615,3.115 1.229,3.313 0.615,0.198 10 false IG 0.104,0.125 0.719,0.323 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-4 (+B1) - F126-7 (GND1) Power switch off 11 to 14 V
F126-3 (ACC1) - F126-7 (GND1) Power switch on (ACC) 11 to 14 V
F125-1 (IG) - F126-7 (GND1) Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR