Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)
RM32K0E _59 Vehicle Exterior _061311 WINDOW / GLASS _0302412 POWER WINDOW REGULATOR MOTOR(for Front Door) G

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not apply positive (+) auxiliary battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

·

Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

Hide 1.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

a.
E292072C25
1.198,1.479 1.906,1.479 true 1.885,3.417 2.333,3.167 true 1.938,3.823 2.333,4.083 true 1.083,3.167 1.521,3.427 true 1.083,4.083 1.469,3.833 true 2.896,1.333 3.208,1.531 0.313,0.198 10 false *c 0.302,2.604 0.615,2.802 0.313,0.198 10 false *a 1,1.396 1.354,1.76 0.354,0.365 10 false *d 2.323,2.24 2.635,2.438 0.313,0.198 10 false *b 0.938,3.021 1.094,3.219 0.156,0.198 10 false B 0.844,4.021 1.156,4.219 0.313,0.198 10 false UP 2.385,3.031 2.844,3.229 0.458,0.198 10 false GND 2.385,4.021 3,4.219 0.615,0.198 10 false DOWN
*a Component without harness connected
(Power Window Regulator Motor Assembly LH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Connect a positive (+) auxiliary battery lead to connector terminal 2 (B).

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates clockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates counterclockwise


If the result is not as specified, replace the power window regulator motor assembly LH.



Hide 2.INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

a.
E292071C22
1.563,1.479 2.604,1.479 true 1.885,3.417 2.333,3.167 true 1.083,3.167 1.521,3.427 true 1.083,4.083 1.469,3.823 true 1.938,3.813 2.333,4.083 true 2.646,1.417 2.958,1.615 0.313,0.198 10 false *d 0.26,2.583 0.573,2.781 0.313,0.198 10 false *a 0.531,1.302 0.99,1.5 0.458,0.198 10 false *b 1.115,2.219 1.531,2.531 0.417,0.313 10 false *c 0.917,3.021 1.073,3.219 0.156,0.198 10 false B 0.833,4.052 1.146,4.25 0.313,0.198 10 false UP 2.396,3.021 2.854,3.219 0.458,0.198 10 false GND 2.396,4.021 3.01,4.219 0.615,0.198 10 false DOWN
*a Component without harness connected
(Power Window Regulator Motor Assembly RH)
*b Clockwise
*c Counterclockwise
*d Motor Gear


Connect a positive (+) auxiliary battery lead to connector terminal 2 (B).

NOTICE:

Do not connect a positive (+) auxiliary battery lead to any terminals other than terminal 2 (B) to avoid damaging the pulse sensor inside the motor.



b.

Connect a negative (-) auxiliary battery lead to connector terminals 1 (GND) and 7 (DOWN) or 10 (UP).


c.

Check that the motor gear rotates smoothly as follows:

OK:
Measurement Condition Specified Condition
1.

Connect the positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 10 (UP).


Motor gear rotates counterclockwise
1.

Connect a positive (+) auxiliary battery lead to terminal 2 (B), connect a negative (-) auxiliary battery lead to terminal 1 (GND), and keep them connected for 3 seconds or more.

2.

With terminals 2 (B) and 1 (GND) connected, connect a negative (-) auxiliary battery lead to terminal 7 (DOWN).


Motor gear rotates clockwise


If the result is not as specified, replace the power window regulator motor assembly RH.