Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2016.10–2019.09
RM32K0E _56 Audio / Visual / Telematics _061290 NAVIGATION / MULTI INFO DISPLAY _0302427 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnostic procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E360248E05
0.385,3.458 0.698,3.656 0.313,0.198 10 false j1 5.906,3.688 7,3.958 1.094,0.271 10 false Navigation ECU 1.885,4.208 4.802,4.583 2.917,0.375 10 false : Data Signal (USB Communication Line) 0.365,3.667 1.51,4.083 1.146,0.417 10 false No. 1 Stereo Jack Adapter Assembly 3.302,2.854 4.833,3.052 1.531,0.198 10 false (Shielded) 0.938,2.438 2.125,2.74 1.188,0.302 10 false UP1 5.969,0.594 7.156,0.896 1.188,0.302 10 false USV1 0.854,1.188 2.042,1.49 1.188,0.302 10 false UDO+ 0.854,0.615 2.042,0.917 1.188,0.302 10 false UJSG 0.875,3.063 2.063,3.365 1.188,0.302 10 false UJSS 0.865,1.792 2.052,2.094 1.188,0.302 10 false UDO- 5.969,1.198 7.156,1.5 1.188,0.302 10 false US1- 5.958,1.792 7.146,2.094 1.188,0.302 10 false US1+ 5.958,2.448 7.146,2.75 1.188,0.302 10 false UGD1 5.938,3.063 7.125,3.365 1.188,0.302 10 false USG1 5.896,3.49 6.208,3.688 0.313,0.198 10 false j3 1.313,2.323 1.573,2.51 0.26,0.188 10 false 1 5.771,0.51 6.031,0.698 0.26,0.188 10 false 1 1.313,1.656 1.573,1.844 0.26,0.188 10 false 2 5.771,1.031 6.031,1.219 0.26,0.188 10 false 2 5.771,1.656 6.031,1.844 0.26,0.188 10 false 3 1.313,1.063 1.573,1.25 0.26,0.188 10 false 3 1.323,0.49 1.583,0.677 0.26,0.188 10 false 4 5.781,2.313 6.042,2.5 0.26,0.188 10 false 4 1.313,2.927 1.573,3.115 0.26,0.188 10 false 5 5.781,2.927 6.042,3.115 0.26,0.188 10 false 5

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while to begin playback.

·

When using a USB device, files that are copy protection or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION


Result:
Result Proceed to
No playable files exist, or incompatible device format or version. A
Playable files exist, and compatible device format or version. B




A

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)

B

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the j3 navigation ECU connector.


b.

Disconnect the j1 No. 1 stereo jack adapter assembly connector.


c.
E360249C05
1.49,0.125 1.938,0.427 0.448,0.302 1.5,2.281 1.948,2.583 0.448,0.302 1.156,1.833 1.594,1.458 true 1.833,1.292 2.313,1.292 true 1.792,1.552 2.104,1.958 true 1.823,3.448 2.375,3.729 true 1.792,3.542 2.344,4.031 true 1.063,3.885 1.625,3.448 true 1.833,1.458 2.271,1.656 true 1.104,1.292 1.583,1.292 true 1.948,3.427 2.521,3.427 true 0.917,3.427 1.49,3.427 true 1.656,0.188 1.969,0.385 0.313,0.198 10 false j3 1.656,2.344 1.969,2.542 0.313,0.198 10 false j1 0.833,1.823 1.219,2.021 0.385,0.198 10 false US1+ 2.344,1.594 2.729,1.792 0.385,0.198 10 false US1- 2.146,1.917 2.615,2.198 0.469,0.281 10 false USG1 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.146,2.698 0.458,2.896 0.313,0.198 10 false *b 0.688,3.823 1.125,4.021 0.438,0.198 10 false UDO- 2.417,3.656 2.854,3.854 0.438,0.198 10 false UDO+ 2.375,4.031 2.854,4.302 0.479,0.271 10 false UJSS 2.344,1.229 2.802,1.448 0.458,0.219 10 false USV1 0.729,1.208 1.188,1.427 0.458,0.219 10 false UGD1 2.552,3.365 3.031,3.635 0.479,0.271 10 false UJSG 0.615,3.344 1,3.573 0.385,0.229 10 false UP1
*a Front view of wire harness connector
(to Navigation ECU)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j1-1 (UP1) - j3-1 (USV1) Always Below 1 Ω
j1-2 (UDO-) - j3-2 (US1-) Always Below 1 Ω
j1-3 (UDO+) - j3-3 (US1+) Always Below 1 Ω
j1-4 (UJSG) - j3-4 (UGD1) Always Below 1 Ω
j1-5 (UJSS) - j3-5 (USG1) Always Below 1 Ω
j1-1 (UP1) - Body ground Always 10 kΩ or higher
j1-2 (UDO-) - Body ground Always 10 kΩ or higher
j1-3 (UDO+) - Body ground Always 10 kΩ or higher
j1-4 (UJSG) - Body ground Always 10 kΩ or higher
j1-5 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NAVIGATION ECU (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NAVIGATION ECU (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.

Reconnect the j3 navigation ECU connector.


b.
E226479C74
1.5,0.906 1.979,1.156 0.479,0.25 1.938,2.083 2.531,2.302 true 1.49,2.083 0.844,2.302 true 1.677,0.948 2.042,1.208 0.365,0.26 10 false j1 2.552,2.281 2.979,2.427 0.427,0.146 10 false UJSG 0.563,2.26 0.927,2.458 0.365,0.198 10 false UP1 0.188,0.167 0.385,0.333 0.198,0.167 10 false *a
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
j1-1 (UP1) - j1-4 (UJSG) Power switch on (ACC) 5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that a backup of the music data is available before performing this operation.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the power switch off.

HINT:

When this malfunction occurs, it is necessary to turn the power switch off to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the power switch on (ACC).


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>SYSTEM DESCRIPTION




Result:
Proceed to
NEXT



NEXT

6.CHECK USB DEVICE OR "iPod"
6.CHECK USB DEVICE OR "iPod"
a.

Check if a USB device or "iPod" is recognized by the navigation ECU, and if information such as track, artist and album names is displayed on the screen.

OK:

USB device or "iPod" is recognized properly and the information is displayed on the screen.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE