Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2016.10–2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0303369 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light. The sensor creates an electrical signal based on the amount of light detected, and sends the signal to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1244 Light Sensor Circuit Malfunction Any of the following conditions is met:
·

Malfunction in automatic light control sensor

·

Open in automatic light control sensor circuit

·

Short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


-

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition Power switch on (IG) ○ ○ ○
Malfunction Status Malfunction in automatic light control sensor ○ - -
Open in automatic light control sensor circuit - ○ -
Short in automatic light control sensor circuit - - ○
Detection Time - - -
Number of Trips 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

E309009E07
2.104,0.531 2.719,0.729 0.615,0.198 10 false CLTB 2.115,1.313 2.729,1.51 0.615,0.198 10 false CLTS 2.125,2.115 2.74,2.313 0.615,0.198 10 false CLTE 0.583,2.771 1.198,2.969 0.615,0.198 10 false G1 0.583,2.927 2.76,3.219 2.177,0.292 10 false Automatic Light Control Sensor 2.573,0.531 3.188,0.729 0.615,0.198 10 false 1 2.573,1.313 3.188,1.51 0.615,0.198 10 false 4 2.583,2.115 3.198,2.313 0.615,0.198 10 false 2 5.375,0.531 5.688,0.802 0.313,0.271 10 false 19 5.396,1.313 5.708,1.583 0.313,0.271 10 false 20 5.396,2.104 5.708,2.375 0.313,0.271 10 false 21 5.333,2.74 5.948,2.938 0.615,0.198 10 false F15 5.333,2.896 6.969,3.313 1.635,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 5.646,0.625 6.26,0.823 0.615,0.198 10 false CLTB 5.646,1.427 6.26,1.625 0.615,0.198 10 false CLTS 5.646,2.219 6.26,2.417 0.615,0.198 10 false CLTE

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light level -
Body Electrical > Main Body > Data List
Tester Display
Light Sensor Illuminance
50003 123 279
OK:

Normal condition listed above is displayed.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G1 automatic light control sensor connector.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-21 (CLTE) - G1-2 (CLTE) Always Below 1 Ω
F15-20 (CLTS) - G1-4 (CLTS) Always Below 1 Ω
F15-19 (CLTB) - G1-1 (CLTB) Always Below 1 Ω
F15-21 (CLTE) or G1-2 (CLTE) - Body ground Always 10 kΩ or higher
F15-20 (CLTS) or G1-4 (CLTS) - Body ground Always 10 kΩ or higher
F15-19 (CLTB) or G1-1 (CLTB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
E173035C47
1.552,0.563 1.917,0.823 0.365,0.26 1.354,2.708 2.344,2 true 2.396,2.708 2.563,2 true 0.146,0.135 0.604,0.438 0.458,0.302 10 false *a 1.146,2.76 1.625,2.979 0.479,0.219 10 false CLTE 2.208,2.75 2.979,3.063 0.771,0.313 10 false CLTB 1.625,0.604 1.927,0.823 0.302,0.219 10 false F15
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))


Reconnect the F15 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F15-19 (CLTB) - F15-21 (CLTE) Power switch off Below 1 V
Power switch on (IG) 11 to 14 V



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
E259758C67
1.531,0.271 1.927,0.49 0.396,0.219 1.833,1.177 2.385,0.885 true 1.458,1.167 0.896,0.896 true 0.188,0.135 0.438,0.313 0.25,0.177 10 false *a 1.656,0.292 2.25,0.74 0.594,0.448 10 false G1 0.542,0.771 0.958,0.948 0.417,0.177 10 false CLTS 2.438,0.792 2.833,0.958 0.396,0.167 10 false CLTE
*a Component with harness connected
(Automatic Light Control Sensor)


Reconnect the G1 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.


c.
E276298N01
2.844,1.646 3.219,1.813 0.375,0.167 10 false GND

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
G1-2 (CLTE) - G1-4 (CLTS) 2 V/DIV., 10 ms./DIV. Power switch on (IG), light control switch in AUTO position Correct waveform is as shown


HINT:

The communication waveform changes according to the surrounding brightness.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE AUTOMATIC LIGHT CONTROL SENSOR