Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2016.10–2019.09
RM32K0E _59 Vehicle Exterior _061162 LIGHTING (EXT) _0303369 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E357711E05
0.135,0.594 1,1.073 0.865,0.479 10 false from Auxiliary Battery 0.219,1.375 2.292,2.458 2.073,1.083 10 false to Taillights, License Plate Lights and Rear Lights*1 1.958,0.833 2.563,1.135 0.604,0.302 10 false J/B-AM 3.458,1.375 4.063,1.677 0.604,0.302 10 false 3H 3.448,0.646 4.052,0.948 0.604,0.302 10 false 3K 3.438,0.479 4.042,0.781 0.604,0.302 10 false 1 3.448,1.188 4.052,1.49 0.604,0.302 10 false 30 5.719,2.323 6.323,2.625 0.604,0.302 10 false 14 5.708,2.521 6.313,2.823 0.604,0.302 10 false MB 6.042,2.417 6.646,2.719 0.604,0.302 10 false TRLY 5.49,3.646 7.156,4.521 1.667,0.875 10 false Main Body ECU (Multiplex Network Body ECU) 3.396,3.24 5.385,3.969 1.99,0.729 10 false Instrument Panel Junction Block Assembly 3.99,1.542 4.594,1.844 0.604,0.302 10 false TAIL 4.781,1.938 5.385,2.24 0.604,0.302 10 false TAIL 0.271,4.167 2.135,4.458 1.865,0.292 10 false *1: for LED Headlight


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillight relay operates. (Taillights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3K-1 - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the auxiliary battery to terminal 3K-1.


d.

Connect a negative (-) lead from the auxiliary battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

E339586C05
1.75,0.49 2.135,0.729 0.385,0.24 4.417,0.458 4.802,0.698 0.385,0.24 3.344,2.208 3.729,2.448 0.385,0.24 3.083,3.333 3.281,2.885 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 1.865,0.531 2.177,0.729 0.313,0.198 10 false 3K 4.521,0.479 4.833,0.677 0.313,0.198 10 false 3H 3.427,2.229 3.74,2.427 0.313,0.198 10 false MB 2.896,3.344 3.396,3.573 0.5,0.229 10 false TRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Switch Condition Specified Condition
3H-30 - Auxiliary battery negative (-) terminal Power switch off 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY