Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511  Torque Sensor1  C1512  Torque Sensor2  C1513  Torque Sensor Deviation Excessive  C1514  Torque Sensor Power Supply Voltage  C1517  Torque Hold  


DESCRIPTION

The torque sensor converts the rotational torque received from the steering wheel into electric signals and sends them to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1511 Torque Sensor1 Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the power switch is turned on (IG) again -
C1512 Torque Sensor2 Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the power switch is turned on (IG) again -
C1513 Torque Sensor Deviation Excessive Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on The ECU judges the system has returned to normal or the power switch is turned on (IG) again -
C1514 Torque Sensor Power Supply Voltage Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Power switch on (IG) again -
C1517 Torque Hold Torque sensor malfunction
·

Torque sensor (Electric power steering column sub-assembly)

·

Power steering ECU assembly


EPS warning light: Comes on Power switch on (IG) again -

WIRING DIAGRAM

C319559E15
0.604,3.229 3.021,3.615 2.417,0.385 10 false Torque Sensor (Electric Power Steering Column Sub-assembly) 4.969,3.375 5.969,3.823 1,0.448 10 false Power Steering ECU Assembly 4.969,3.208 6.094,3.729 1.125,0.521 10 false z14 5.021,0.698 5.521,0.938 0.5,0.24 10 false TRQV1 5.031,1.104 5.531,1.344 0.5,0.24 10 false TRQ1 5.031,1.49 5.531,1.729 0.5,0.24 10 false TRQG1 5.031,1.896 5.531,2.135 0.5,0.24 10 false TRQV2 5.042,2.281 5.542,2.521 0.5,0.24 10 false TRQ2 5.031,2.667 5.531,2.906 0.5,0.24 10 false TRQG2 4.833,0.594 5.042,0.823 0.208,0.229 10 false 7 4.833,1.01 5.042,1.24 0.208,0.229 10 false 9 4.833,1.406 5.042,1.635 0.208,0.229 10 false 8 4.833,1.792 5.042,2.021 0.208,0.229 10 false 3 4.833,2.188 5.042,2.417 0.208,0.229 10 false 1 4.833,2.583 5.042,2.813 0.208,0.229 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric power steering column sub-assembly has been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connection condition of the torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)

NG

CONNECT CONNECTOR

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV VOLTAGE)
a.
C319556C37
1.479,0.333 1.979,0.583 0.5,0.25 0.958,0.771 1.677,1.635 true 2.521,1.302 1.958,2.135 true 2.531,2.875 1.74,2.302 true 0.865,2.74 1.531,1.792 true 0.229,0.188 0.542,0.344 0.313,0.156 10 false *a 0.448,0.698 0.927,0.979 0.479,0.281 10 false TRQG2 2.365,2.885 2.844,3.167 0.479,0.281 10 false TRQG1 2.573,1.219 3.052,1.5 0.479,0.281 10 false TRQV1 0.646,2.76 1.125,3.042 0.479,0.281 10 false TRQV2 1.615,0.333 2.094,0.615 0.479,0.281 10 false z14
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the power switch to on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z14-7 (TRQV1) - z14-8 (TRQG1) power switch on (IG) 4.5 to 5.5 V
z14-3 (TRQV2) - z14-2 (TRQG2) power switch on (IG) 4.5 to 5.5 V



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
C319556C38
1.479,0.333 1.979,0.583 0.5,0.25 0.958,0.771 1.677,1.635 true 2.49,1.073 1.99,1.688 true 2.531,2.875 1.74,2.302 true 0.865,2.948 1.5,2.313 true 0.229,0.24 0.542,0.396 0.313,0.156 10 false *a 0.458,0.698 0.938,0.979 0.479,0.281 10 false TRQG2 2.344,2.896 2.823,3.177 0.479,0.281 10 false TRQG1 2.542,1.01 3.021,1.292 0.479,0.281 10 false TRQ2 0.656,2.948 1.135,3.229 0.479,0.281 10 false TRQ1 1.604,0.333 2.083,0.615 0.479,0.281 10 false z14
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the power switch on (READY).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z14-9 (TRQ1) - z14-8 (TRQG1) Power switch on (READY) and steering wheel not being turned (without load) 2.3 to 2.7 V
Power switch on (READY) and steering wheel being turned to the right with vehicle stopped 2.5 to 3.8 V
Power switch on (READY) and steering wheel being turned to the left with vehicle stopped 1.2 to 2.5 V
z14-1 (TRQ2) - z14-2 (TRQG2) Power switch on (READY) and steering wheel not being turned (without load) 2.3 to 2.7 V
Power switch on (READY) and steering wheel being turned to the right with vehicle stopped 1.2 to 2.5 V
Power switch on (READY) and steering wheel being turned to the left with vehicle stopped 2.5 to 3.8 V



c.

Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

Standard Voltage:
Tester Connection Condition Specified Condition
Sum of voltage between z14-9 (TRQ1) and z14-8 (TRQG1) and voltage between z14-1 (TRQ2) and z14-2 (TRQG2) Power switch on (READY) and steering wheel not being turned (without load) Between 4.75 V and 5.25 V
Power switch on (READY) and steering wheel being turned to the right with vehicle stopped
Power switch on (READY) and steering wheel being turned to the left with vehicle stopped



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY