Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552  PIG Power Supply Voltage  C1554  Power Supply Relay Failure  


DESCRIPTION

If a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop power assist. The ECU must be replaced when there is a problem with the relays because the relays are built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1552 PIG Power Supply Voltage PIG power source circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on Power switch on (IG) again -
C1554 Power Supply Relay Failure Power source relay circuit malfunction
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


EPS warning light: Comes on Power switch on (IG) again -

WIRING DIAGRAM

C322363E16
5.615,2.99 6.625,3.417 1.01,0.427 10 false Power Steering ECU Assembly 1.458,0.708 3.177,1.083 1.719,0.375 10 false from Auxiliary Battery 3.833,0.896 4.375,1.156 0.542,0.26 10 false EPS 5.677,0.74 6.219,1 0.542,0.26 10 false PIG 5.677,1.906 6.219,2.167 0.542,0.26 10 false PGND 5.51,0.625 6.052,0.885 0.542,0.26 10 false 1 5.5,1.792 6.042,2.052 0.542,0.26 10 false 2 5.625,2.823 6.167,3.083 0.542,0.26 10 false F68

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the F68 power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F68-1 (PIG) - Body ground Power switch on (IG) 9 to 16 V



c.
C349134C07
1.5,0.167 2,0.417 0.5,0.25 2.417,1.771 2,1.271 true 1.448,1.271 1.031,1.771 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.635,0.188 2.031,0.354 0.396,0.167 10 false F68 2.219,1.792 2.698,1.958 0.479,0.167 10 false PGND 0.917,1.792 1.396,1.958 0.479,0.167 10 false PIG
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F68-2 (PGND) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR