FREEZE FRAME DATA
It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specification.
Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the GTS.
Turn the power switch off.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Check the freeze frame data on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from speedometer | Min.: 0.0 km/h (0.0 MPH)
Max.: 300.0 km/h (186.4 MPH) |
·
0 km/h (0 MPH): Power switch on (READY) and vehicle stopped ·
No significant fluctuation: Power switch on (READY) and vehicle driven at a constant speed |
- |
| Wheel Speed Right | Rear right wheel speed | Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH) |
·
0 km/h (0 MPH): Power switch on (READY) and vehicle stopped ·
No significant fluctuation: Power switch on (READY) and vehicle driven at a constant speed |
- |
| Wheel Speed Left | Rear left wheel speed | Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH) |
·
0 km/h (0 MPH): Power switch on (READY) and vehicle stopped ·
No significant fluctuation: Power switch on (READY) and vehicle driven at a constant speed |
- |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
No significant fluctuation | Engine running at a constant speed |
| Motor Actual Current | Amount of current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right |
Power switch on (READY) and steering wheel being turned |
| Command Value Current | Requested current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right |
Power switch on (READY) and steering wheel being turned |
| Steering Angle Velocity | Steering angle speed | Min.: -32768 deg/s
Max.: 32767 deg/s |
Value changes in proportion to steering speed
- The value increases when turning left and decreases when turning right |
Power switch on (READY) and steering wheel being turned |
| Thermistor Temperature | ECU substrate temperature | Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F) |
-50°C to 150°C (-58°F to 302°F) | - |
| IG Power Supply | IG power source voltage | Min.: 0.0000 V
Max.: 20.1531 V |
8 to 16 V | Power switch on (IG) |
| Steering Wheel Torque | Steering wheel torque | Min.: -7.00 Nm
Max.: 7.00 Nm |
Value changes in proportion to steering effort
- The value increases when turning left and decreases when turning right |
Power switch on (READY) and steering wheel being turned |
| Motor Rotation Angle | Motor rotation angle | Min.: 0.000 deg
Max.: 360.000 deg |
During steering operation, motor rotation angle value changes from 0 to 360° | Power switch on (READY) and steering wheel being turned |
| Command Val Current 2 | Requested current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor Voltage | Motor power supply voltage | Min.: 0.000 V
Max.: 98.000 V |
9 to 16 V | Power switch on (READY) and steering wheel being turned |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Power switch on (READY) and steering wheel not being turned (without load) |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Power switch on (READY) and steering wheel not being turned (without load) |
| PS Assist Signal | Status of the record of power steering assist signal | OFF or ON | OFF: Power switch on (IG)
ON: Power switch on (READY) |
- |
| Ready Status | Ready status | Ready or OFF | Ready or OFF | - |
| Motor Actual Current 2 | Amount of current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Steering Angle | Steering angle | Min.: -3072.0 deg
Max.: 3070.5 deg |
- | - |
| Torque Sensor 1 Output | Torque sensor 1 output value | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Torque Sensor 2 Output | Torque sensor 2 output value | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Torque Sensor 1 Power Supply | Torque sensor 1 power supply voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Torque Sensor 2 Power Supply | Torque sensor 2 power supply voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Rotation Angle Sensor Output 1 | Rotation angle sensor Vx1 output voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Rotation Angle Sensor Output 2 | Rotation angle sensor Vx2 output voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Rotation Angle Sensor Output 3 | Rotation angle sensor Vy1 output voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Rotation Angle Sensor Output 4 | Rotation angle sensor Vy2 output voltage | Min.: 0.0000 V
Max.: 4.9725 V |
- | - |
| Motor 1 Terminal Current (U) | Motor 1 terminal current (U phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 1 Terminal Current (V) | Motor 1 terminal current (V phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 1 Terminal Current (W) | Motor 1 terminal current (W phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Current (U) | Motor 2 terminal current (U phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Current (V) | Motor 2 terminal current (V phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Current (W) | Motor 2 terminal current (W phase) | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort | Power switch on (READY) and steering wheel being turned |
| Motor 1 U Phase Duty | Motor 1 U phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 1 V Phase Duty | Motor 1 V phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 1 W Phase Duty | Motor 1 W phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 2 U Phase Duty | Motor 2 U phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 2 V Phase Duty | Motor 2 V phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 2 W Phase Duty | Motor 2 W phase duty | Min.: 0.00%
Max.: 100.00% |
- | - |
| Motor 1 Terminal Volt (U) | Motor 1 terminal voltage (U phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 1 Terminal Volt (V) | Motor 1 terminal voltage (V phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 1 Terminal Volt (W) | Motor 1 terminal voltage (W phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Volt (U) | Motor 2 terminal voltage (U phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Volt (V) | Motor 2 terminal voltage (V phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 2 Terminal Volt (W) | Motor 2 terminal voltage (W phase) | Min.: 0.000 V
Max.: 98.000 V |
Value changes within 4 to 35 V range | Power switch on (READY) and steering wheel being turned |
| Motor 1 PIG Power Supply | Power supply voltage to active motor 1 | Min.: 0.0000 V
Max.: 20.1531 V |
9 to 16 V | Power switch on (READY) and steering wheel being turned |
| Motor 2 PIG Power Supply | Power supply voltage to active motor 2 | Min.: 0.0000 V
Max.: 20.1531 V |
9 to 16 V | Power switch on (READY) and steering wheel being turned |