Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM32K0E _55 Steering _061342 POWER ASSIST SYSTEMS _0303420 POWER STEERING SYSTEM J

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  EPS Warning Light Circuit  


DESCRIPTION

If the power steering ECU assembly detects a malfunction, the power steering ECU assembly stores a DTC and illuminates the EPS warning light.

WIRING DIAGRAM

C322366E16
1.74,0.49 2.354,0.688 0.615,0.198 10 false CANH 1.75,0.875 2.365,1.073 0.615,0.198 10 false CANL 2.229,0.365 2.844,0.563 0.615,0.198 10 false 32 2.229,0.76 2.844,0.958 0.615,0.198 10 false 31 0.844,1.073 1.458,1.271 0.615,0.198 10 false F4 1.438,1.938 2.927,2.156 1.49,0.219 10 false from IG1-NO. 1 Relay 3.708,2.104 4.396,2.344 0.688,0.24 10 false EPS-IG1 5.292,0.51 5.906,0.708 0.615,0.198 10 false F23 5.292,0.906 5.906,1.104 0.615,0.198 10 false F23 5.385,0.729 6,0.927 0.615,0.198 10 false 8 5.385,0.323 6,0.521 0.615,0.198 10 false 7 5.698,0.51 6.313,0.708 0.615,0.198 10 false CANH 5.688,0.906 6.302,1.104 0.615,0.198 10 false CANL 5.688,1.958 6.302,2.156 0.615,0.198 10 false IG 5.698,2.563 6.313,2.76 0.615,0.198 10 false PIG 5.677,3.229 6.292,3.427 0.615,0.198 10 false PGND 3.813,2.719 5.188,2.917 1.375,0.198 10 false EPS 5.292,1.948 5.906,2.146 0.615,0.198 10 false F23 5.292,2.563 5.906,2.76 0.615,0.198 10 false F68 5.292,3.219 5.906,3.417 0.615,0.198 10 false F68 5.365,1.771 5.688,1.958 0.323,0.188 10 false 1 5.375,2.365 5.698,2.552 0.323,0.188 10 false 1 5.385,3.031 5.708,3.219 0.323,0.188 10 false 2 1.438,2.542 3.906,2.792 2.469,0.25 10 false from Auxiliary Battery 0.833,1.24 2.719,1.469 1.885,0.229 10 false Combination Meter Assembly 0.792,4.323 2.885,4.531 2.094,0.208 10 false : CAN Communication Line 5.625,3.813 6.625,4.24 1,0.427 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK ASSIST LIMIT RECORD
a.

Using the GTS, read the Data List item "Assist Limit Record 1".

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Assist Limit Record 1 Information of assist limit that was used in the past or is currently in use (latest history) Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, Vhcl Spd Sig Malf, Batt Vol Keep - -
Chassis > EMPS > Data List
Tester Display
Assist Limit Record 1
50003 142 73
HINT:

For the Data List item "Assist Limit Record 1", each item in the Range is described below.

Range Description
Mtr Overheat When the vehicle is stopped or traveling at low speed, and steering operations are performed repeatedly or the steering wheel is turned all the way to the side and held there for a long time, assist may be limited in order to prevent overheating of the power steering motor assembly and power steering ECU assembly.
After 10 minutes elapse with the engine stopped and no steering operations being performed, the system will return to normal.
After recovering from the overheated condition, assist can be performed as usual.
Pow Vol Low When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be stopped.
After the battery condition returns to normal, assist can be performed as usual.
Pow Vol Low Prevent When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.
Eng Stall When the engine stalls, battery charge becomes insufficient, so assist is stopped.
After recovering from the engine stall, assist can be performed as usual.
Ready OFF After Ready ON, if a malfunction in the HV system etc. causes a return to Ready OFF, the HV battery charge becomes insufficient, so assist is stopped.
After returning to Ready ON state, assist can be performed as usual.
Mtr Overload When the steering wheel cannot turn, such as when a road wheel is against a curb, if the driver continues to apply force to the steering wheel, current to the motor may be limited to prevent overheating.
When the steering wheel is returned to a neutral position, assist can be performed as usual.
DC-DC Malf If there is a malfunction in the DC-DC converter, etc., assist may be limited.
After the DC-DC converter returns to normal, assist can be performed as usual.
Vhcl Spd Sig Malf If the vehicle speed signal is abnormal due to a wheel speed sensor malfunction, etc., assist may be limited.
Batt Vol Keep When insufficient battery charge, or battery degradation etc. causes the voltage to temporarily decrease, assist may be limited.
After the battery condition returns to normal, assist can be performed as usual.



b.

Based on the "Assist Limit Record 1" information, the following Data List items and the information from the customer interview, explain the situation to the customer.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Record 1 Key Cycle Number of times that the power switch was turned on (IG) before Assist Limit Record 1 was stored Min.: 0 times
Max.: 65535 times
- -
Record 1 Key Cycle Elapsed Time Period of time that elapsed since the power switch was turned on (IG) before Assist Limit Record 1 was stored Min.: 0.0 s
Max.: 53687091.1 s
- -
Chassis > EMPS > Data List
Tester Display
Record 1 Key Cycle
Record 1 Key Cycle Elapsed Time
50003 142 74,75
Result:
Result Proceed to
"Unrec" is displayed A
Other than Unrec is displayed B


HINT:

If it is necessary to investigate further into the past, check the "Assist Limit Record 2" and "Assist Limit Record 3" information in the same way as "Assist Limit Record 1".




A

2.CHECK HARNESS AND CONNECTOR

B

EXPLAIN THE CHECKED "ASSIST LIMIT RECORD 1" TO THE CUSTOMER, CROSS-CHECKING THE DATA LIST ITEMS WITH THE INFORMATION FROM THE CUSTOMER INTERVIEW.

2.CHECK HARNESS AND CONNECTOR
a.

Jiggle the power steering ECU assembly connectors and wire harness up and down, and left and right to check the illumination condition of the EPS warning light in the combination meter assembly.

OK:

The EPS warning light illumination condition does not change.


HINT:

When the EPS warning light is operating properly, it illuminates when the power switch is turned on (IG) and turns off when the power switch is turn on (READY).



Result:
Proceed to
OK
NG



OK

3.CHECK CAN COMMUNICATION SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output. A
CAN communication system DTCs are output. B



A

4.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)

B

4.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - GROUND)
a.

Disconnect the F68 and F23 power steering ECU assembly connectors.


C349135C04
0.5,0.833 1,1.083 0.5,0.25 0.5,3.333 1,3.583 0.5,0.25 1.01,1.708 1.427,1.292 true 1,4 1.417,3.583 true 2.333,4 2,3.583 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 0.635,3.365 1.094,3.563 0.458,0.198 10 false F68 0.635,0.865 1.094,1.063 0.458,0.198 10 false F23 0.792,4.01 1.25,4.208 0.458,0.198 10 false PIG 0.802,1.625 1.26,1.823 0.458,0.198 10 false IG 2.333,4 2.917,4.25 0.583,0.25 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F23-1 (IG) - Body ground Power switch on (IG) 8 to 16 V
F68-1 (PIG) - Body ground Power switch on (IG) 9 to 16 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F68-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMBINATION METER ASSEMBLY
a.

Connect the F68 and F23 power steering ECU assembly connectors.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. EPS
50004 122 22

c.

Check the combination meter assembly.

OK:

The EPS warning light turns on or off in accordance with the GTS operation.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER STEERING ECU ASSEMBLY

B

REPLACE POWER STEERING ECU ASSEMBLY

C