Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the IG circuit or IG hold circuit of the certification ECU (smart key ECU assembly) is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2271 Ignition Hold Monitor Malfunction When either of the following conditions is met (1-trip detection logic*1):
·

The IG circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*2

·

The IG hold circuit of the certification ECU (smart key ECU assembly) is malfunctioning.*3


·

AM2 fuse

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


DTC Output Confirmation Operation:

Turn the power switch on (IG).



*1: Only detected while a malfunction is present and the power switch is on (IG).

*2: The IG circuit and IG hold circuit activate the IG relay.

*3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in on (IG).


DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Turn the power switch on (IG). ○ ○
Malfunction Status The IG circuit in the certification ECU (smart key ECU assembly) is malfunctioning. ○ -
The IG hold circuit in the certification ECU (smart key ECU assembly) is malfunctioning. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The power switch cannot be turned on (IG) (the hybrid control system cannot be started). The power source mode cannot be changed to on (IG).

Related Data List and Active Test Items
DTC No. Data List and Active Test
B2271
Power Source Control
·

IG Relay Monitor (Inside)

·

Latch Circuit



WIRING DIAGRAM

E352009E02
1.49,3.188 1.948,3.385 0.458,0.198 10 false AM2 0.156,3.031 1.021,3.615 0.865,0.583 10 false from Auxiliary Battery 2.292,0.667 2.75,0.865 0.458,0.198 10 false IC 1.979,2.948 2.438,3.146 0.458,0.198 10 false 4 2.208,3.031 2.667,3.229 0.458,0.198 10 false +B 1.906,6.448 2.365,6.646 0.458,0.198 10 false 18 2.208,6.531 2.667,6.729 0.458,0.198 10 false E 2.656,0.313 3.115,0.51 0.458,0.198 10 false +B 2.823,0.719 3.281,0.917 0.458,0.198 10 false IG1D 3.281,0.719 3.74,0.917 0.458,0.198 10 false 17 3.646,0.635 4.104,0.833 0.458,0.198 10 false 17 3.646,0.823 4.104,1.021 0.458,0.198 10 false 3A 3.646,0.427 4.104,0.625 0.458,0.198 10 false 3K 3.688,0.24 4.146,0.438 0.458,0.198 10 false 1 1.854,7 2.313,7.198 0.458,0.198 10 false F1 1.854,7.156 3.417,7.594 1.563,0.438 10 false Certification ECU (Smart Key ECU Assembly) 4.469,7.146 6.125,7.375 1.656,0.229 10 false No. 1 Integration Relay 4.469,6.979 4.854,7.198 0.385,0.219 10 false 1A 3.573,6.156 4.385,6.365 0.813,0.208 10 false IG2-MAIN 3.667,4.927 4.479,5.135 0.813,0.208 10 false WIPER 4.917,5.396 5.729,5.604 0.813,0.208 10 false IG1 NO. 3 4.917,6.625 5.729,6.833 0.813,0.208 10 false IG2 NO. 1 4.594,6.302 5.406,6.51 0.813,0.208 10 false 7 4.521,5.917 5.333,6.125 0.813,0.208 10 false 10 4.594,5.073 5.406,5.281 0.813,0.208 10 false 2 4.594,4.688 5.406,4.896 0.813,0.208 10 false 4 5.74,6.302 5.979,6.5 0.24,0.198 10 false 8 5.74,5.917 5.979,6.115 0.24,0.198 10 false 9 5.74,5.083 5.979,5.281 0.24,0.198 10 false 1 5.74,4.688 5.979,4.885 0.24,0.198 10 false 3 6.01,6.156 6.99,6.427 0.979,0.271 10 false ECU-IG2 NO. 1 3.927,3.802 6.667,4.115 2.74,0.313 10 false Instrument Panel Junction Block Assembly 3.656,3.458 4.115,3.656 0.458,0.198 10 false 3F 3.656,3.052 4.115,3.25 0.458,0.198 10 false 3F 3.656,2.656 4.115,2.854 0.458,0.198 10 false 3L 3.688,2.479 4.146,2.677 0.458,0.198 10 false 1 3.656,2.865 4.115,3.063 0.458,0.198 10 false 13 3.656,3.271 4.115,3.469 0.458,0.198 10 false 12 4.521,3.271 5.333,3.479 0.813,0.208 10 false IG2-NO. 2 4.521,2.135 5.333,2.344 0.813,0.208 10 false IG1-NO. 2 4.521,1.042 5.333,1.25 0.813,0.208 10 false IG1-NO. 1 5.542,0.563 6.625,0.781 1.083,0.219 10 false ECU-IG1 NO. 3 5.708,1.74 6.542,1.958 0.833,0.219 10 false WIPER RR 5.573,2.802 6.719,3.052 1.146,0.25 10 false ECU-IG2 NO. 3 6.688,3.052 7.156,3.208 0.469,0.156 10 false 3D 6.688,2.656 7.156,2.813 0.469,0.156 10 false 3D 6.688,1.594 7.156,1.75 0.469,0.156 10 false 3H 6.688,0.427 7.156,0.583 0.469,0.156 10 false 3F 6.688,0.24 7.156,0.396 0.469,0.156 10 false 10 6.688,1.406 7.156,1.563 0.469,0.156 10 false 12 6.688,2.469 7.156,2.625 0.469,0.156 10 false 19 6.729,2.865 6.979,3.052 0.25,0.188 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses of circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Start Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B416821C30
1.458,2.417 1.958,2.667 0.5,0.25 2.771,3.99 2.292,3.552 true 0.406,3.031 0.719,3.188 0.313,0.156 10 false *a 1.625,2.438 1.979,2.677 0.354,0.24 10 false F1 2.844,3.885 3.167,4.115 0.323,0.229 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-4 (+B) - Body ground Power switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.
B416821C31
1.469,2.417 1.969,2.667 0.5,0.25 0.74,4.229 1.156,3.813 true 0.333,2.917 0.625,3.115 0.292,0.198 10 false *a 1.635,2.438 2.083,2.74 0.448,0.302 10 false F1 0.573,4.125 0.729,4.323 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-18 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B424427C34
1.531,0.083 2.031,0.333 0.5,0.25 0.833,1.917 1.177,0.979 true 0.188,0.188 0.5,0.344 0.313,0.156 10 false *a 1.698,0.104 2.01,0.302 0.313,0.198 10 false F1 0.458,1.813 0.958,2.052 0.5,0.24 10 false IG1D
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Reconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F1-17 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)