Use the following procedure to troubleshoot the rear view monitor system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
The rear view monitor display may be temporarily distorted due to radio waves around the vehicle.
| Problem Symptom | Cause |
|---|---|
|
*: DTCs output as "Hist" will not be output again after DTCs are cleared. |
|
Both of the following conditions are met:
·
The problem symptom indicates a rear view monitor display malfunction and the problem symptom cannot be reproduced. ·
DTC C1622 is output as "Hist" only.* |
The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage.
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs and make a note of any codes that are output.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs. Try to prompt the DTC by simulating the original activity that the DTC suggests.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
The radio and display receiver assembly may store the DTCs of the following system. If DTCs other than those specified in Diagnostic Trouble Code Chart of the rear view monitor system are output, refer to Diagnostic Trouble Code Chart for the applicable system.
| System | Proceed to |
|---|---|
| Audio and Visual System (w/o Navigation System) | ( )
|
| Navigation System (w/ Navigation System) | ( )
|
| Result | Proceed to |
|---|---|
| No DTCs are output | A |
| DTCs are output (w/o Navigation System) | B |
| DTCs are output (w/ Navigation System) | C |
A
B
C
Use the GTS to check if the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| CAN DTCs are not output | A |
| CAN DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Result | Proceed to |
|---|---|
| Symptom does not occur | A |
| Symptom occurs | B |
A
B
| Proceed to |
|---|
| NEXT |
NEXT
w/o Navigation System:
Refer to the audio and visual system.
w/ Navigation System:
Refer to the navigation system.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Symptom does not appear | A |
| Symptom appears (w/o Navigation System) | B |
| Symptom appears (w/ Navigation System) | C |
A
B
C
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
Refer to the problem symptoms table.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in problem symptoms table | A |
| Fault is listed in problem symptoms table | B |
A
B
Refer to the terminals of ECU.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>REAR VIEW MONITOR SYSTEM>TERMINALS OF ECU
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT