Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › 2016.10–2020.08
RM32K0E _58 Vehicle Interior _061839 PRE-COLLISION _0303861 PRE-COLLISION SYSTEM U

PRE-COLLISION  PRE-COLLISION SYSTEM  TERMINALS OF ECU  


CHECK MILLIMETER WAVE RADAR SENSOR


E321782E27
2.167,0.75 2.667,1 0.5,0.25 2.333,0.792 2.792,0.99 0.458,0.198 10 false A2

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-8 (IGB) - A2-1 (SGND) B - W-B Power source Power switch on (IG) 11 to 14 V
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-3 (CA2H) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-2 (CA2L) - A2-1 (SGND) GR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-5 (CA1P) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-6 (CA1N) - A2-1 (SGND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)


c.

WAVEFORM 1

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between A2-3 (CA2H) and A2-1 (SGND)
Between A2-5 (CA1P) and A2-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




d.

WAVEFORM 2

i.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between A2-2 (CA2L) and A2-1 (SGND)
Between A2-6 (CA1N) and A2-1 (SGND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK FORWARD RECOGNITION CAMERA


E256359E75
1.75,0.75 2.25,1 0.5,0.25 1.917,0.792 2.375,0.99 0.458,0.198 10 false R5

a.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

If the result is not as specified, there may be a malfunction on the wire harness side.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-8 (BZ) - R5-10 (GND) B - W-B Pre-collision city buzzer Power switch on (IG), pre-collision city buzzer not operating 11 to 14 V
Power switch on (IG), pre-collision city buzzer operating 0 to 1.5 V
R5-3 (LKSW) - R5-10 (GND) R - W-B Pre-collision system cancel switch assembly Pre-collision system cancel switch assembly being pressed Below 1 Ω
Pre-collision system cancel switch assembly not being pressed 100 kΩ or higher
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch on off Below 1 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-10 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
R5-6 (CANH) - R5-10 (GND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
R5-11 (CA1N) - R5-10 (GND) GR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
R5-12 (CANL) - R5-10 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)


c.

WAVEFORM 1

i.
A086154E97
2.75,0.271 3.365,0.521 0.615,0.25 10 false 1 V/DIV. 1.365,1.906 2.313,2.094 0.948,0.188 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between R5-5 (CA1P) - R5-10 (GND)
Between R5-6 (CANH) - R5-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




d.

WAVEFORM 2

i.
A086155E89
2.76,0.281 3.396,0.51 0.635,0.229 10 false 1 V/DIV. 1.365,1.875 2.333,2.073 0.969,0.198 10 false 10 μsec./DIV.

CAN communication signal

Item Content
Terminal Name Between R5-11 (CA1N) - R5-10 (GND)
Between R5-12 (CANL) - R5-10 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.