Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE
RM32K0E _58 Vehicle Interior _062267 SUPPLEMENTAL RESTRAINT SYSTEMS _0303872 SPIRAL CABLE G

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSPECTION  


PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove the steering sensor from the spiral cable sub-assembly when inspecting the spiral cable sub-assembly.

·

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Visually check the spiral cable sub-assembly for defects.

i.

The defects are as follows:

·

Scratches

·

Small cracks

·

Dents

·

Chips

·

Cracks or other damage to the connector

OK:

No defects are found.



If any of the defects is found, replace the spiral cable sub-assembly with a new one.



b.

Check the spiral cable sub-assembly.

B459830C01
2.417,1.083 2.75,1.25 0.333,0.167 3.833,1.083 4.167,1.25 0.333,0.167 4.667,0.833 5,1 0.333,0.167 6.5,0.833 6.833,1 0.333,0.167 6.167,4.667 6.5,4.833 0.333,0.167 4.333,4.667 4.667,4.833 0.333,0.167 3.833,4.75 4.167,4.917 0.333,0.167 2.521,4.75 2.854,4.917 0.333,0.167 1.438,4.24 1.771,4.406 0.333,0.167 2.25,6.719 2.583,6.885 0.333,0.167 0.417,6.75 0.75,6.917 0.333,0.167 5.563,6.542 5.896,6.708 0.333,0.167 2.177,2.583 2.51,2.75 0.333,0.167 0.469,2.635 0.802,2.802 0.333,0.167 2.646,0.698 2.969,0.969 true 3.031,0.719 3.104,0.958 true 3.563,0.729 3.531,0.958 true 3.833,0.729 3.635,0.969 true 3.823,1.573 3.667,1.427 true 2.802,1.583 3.01,1.438 true 4.729,0.427 5.292,0.823 true 5.063,0.396 5.406,0.823 true 5.438,0.396 5.521,0.813 true 5.781,0.406 5.656,0.813 true 6.052,0.396 5.781,0.813 true 6.521,0.375 5.875,0.813 true 4.781,1.271 5.406,1.01 true 5.073,1.302 5.51,1.021 true 5.333,1.281 5.615,1.021 true 5.708,1.271 5.74,1.021 true 6.094,1.021 6.052,1.271 6.052,1.271 5.875,1.021 true 6.521,1.25 6.25,1 true 1,2.01 1.781,2.5 true 1.375,2 1.781,2.406 true 1.854,2.021 1.813,2.292 true 2.208,2.083 1.948,2.396 true 2.208,2.26 1.969,2.479 true 2.198,2.458 1.969,2.583 true 2.208,2.917 1.958,2.719 true 2.198,3.115 1.958,2.823 true 2.167,3.302 1.948,2.917 true 1.865,3.208 1.823,2.823 true 1.552,3.24 1.781,2.729 true 1.167,3.281 1.781,2.635 true 0.698,2.188 1.177,2.469 true 0.677,2.427 1.167,2.656 true 0.719,3.094 1.177,2.833 true 0.74,3.333 1.167,2.99 true 4.458,4.271 5.021,4.667 true 4.771,4.229 5.146,4.656 true 5.156,4.24 5.24,4.667 true 5.5,4.229 5.375,4.656 true 5.823,4.219 5.469,4.656 true 6.24,4.219 5.604,4.667 true 4.448,5.104 5.125,4.844 true 4.76,5.115 5.24,4.854 true 5.052,5.115 5.344,4.854 true 5.427,5.115 5.458,4.865 true 5.844,4.865 5.802,5.115 5.802,5.115 5.594,4.854 true 6.24,5.094 5.969,4.844 true 2.667,4.344 3.031,4.583 true 3.042,4.333 3.135,4.573 true 3.615,4.344 3.563,4.573 true 3.927,4.344 3.688,4.583 true 3.823,5.229 3.635,5.042 true 2.875,5.219 3.031,5.021 true 1.354,5.125 1.51,4.927 true 1.875,5.125 1.688,4.938 true 5.948,6.271 6.146,6.51 true 6.5,6.271 6.385,6.49 true 1.01,6.146 1.771,6.635 true 1.365,6.125 1.771,6.531 true 1.854,6.125 1.792,6.427 true 2.219,6.208 1.958,6.521 true 2.208,6.396 1.969,6.615 true 2.208,6.583 1.958,6.708 true 2.229,7.063 1.969,6.833 true 2.208,7.271 1.969,6.938 true 2.156,7.427 1.958,7.042 true 1.844,7.354 1.823,6.958 true 1.531,7.396 1.781,6.844 true 1.135,7.406 1.781,6.75 true 0.698,6.313 1.177,6.594 true 0.677,6.542 1.167,6.771 true 0.719,7.219 1.177,6.969 true 0.76,7.469 1.177,7.135 true 0.167,0.104 0.542,0.344 0.375,0.24 10 false *a 0.49,0.104 0.865,0.344 0.375,0.24 12 false *A 2.51,0.521 2.823,0.74 0.313,0.219 10 false D2- 2.906,0.531 3.219,0.75 0.313,0.219 10 false D2+ 3.5,0.542 3.74,0.76 0.24,0.219 10 false D- 3.802,0.552 4.042,0.771 0.24,0.219 10 false D+ 3.917,1.083 4.156,1.302 0.24,0.219 10 false z2 2.51,1.083 2.75,1.302 0.24,0.219 10 false z3 2.635,1.51 2.948,1.729 0.313,0.219 10 false *c 3.875,1.521 4.188,1.74 0.313,0.219 10 false *b 4.573,0.219 4.885,0.438 0.313,0.219 10 false IL-2 4.896,0.208 5.208,0.427 0.313,0.219 10 false IL+2 5.281,0.208 5.594,0.427 0.313,0.219 10 false DIST 5.625,0.208 6.073,0.427 0.448,0.219 10 false +DP2 6.021,0.208 6.469,0.427 0.448,0.219 10 false +DP 6.417,0.198 6.708,0.396 0.292,0.198 10 false HO 6.594,0.823 6.885,1.021 0.292,0.198 10 false z4 4.76,0.833 5.052,1.031 0.292,0.198 10 false z1 4.563,1.302 4.875,1.521 0.313,0.219 10 false AU1 4.875,1.333 5.188,1.552 0.313,0.219 10 false AU2 5.208,1.313 5.521,1.531 0.313,0.219 10 false ASL 5.563,1.302 5.875,1.521 0.313,0.219 10 false EAU 5.948,1.302 6.26,1.521 0.313,0.219 10 false ECC 6.427,1.281 6.74,1.5 0.313,0.219 10 false CCS 0.813,1.833 1.125,2.052 0.313,0.219 10 false EAU 1.198,1.823 1.51,2.042 0.313,0.219 10 false ECC 1.719,1.833 2.031,2.052 0.313,0.219 10 false CCS 2.25,1.948 2.563,2.167 0.313,0.219 10 false HO 2.25,2.146 2.563,2.365 0.313,0.219 10 false +DP 2.24,2.344 2.729,2.563 0.49,0.219 10 false +DP2 2.219,2.583 2.635,2.802 0.417,0.219 10 false F29 2.271,2.844 2.688,3.063 0.417,0.219 10 false DIST 2.26,3.073 2.677,3.292 0.417,0.219 10 false IL+2 2.25,3.271 2.667,3.49 0.417,0.219 10 false IL-2 1.76,3.271 2.073,3.49 0.313,0.219 10 false AU1 1.396,3.302 1.708,3.521 0.313,0.219 10 false AU2 0.99,3.313 1.302,3.531 0.313,0.219 10 false ASL 0.479,2.052 0.792,2.271 0.313,0.219 10 false D+ 0.479,2.323 0.719,2.542 0.24,0.219 10 false D- 0.521,2.635 0.938,2.854 0.417,0.219 10 false F30 0.448,3.031 0.76,3.25 0.313,0.219 10 false D2- 0.438,3.26 0.75,3.479 0.313,0.219 10 false D2+ 0.531,3.948 0.906,4.188 0.375,0.24 12 false *B 4.281,4.042 4.594,4.26 0.313,0.219 10 false IL-2 4.635,4.042 4.948,4.26 0.313,0.219 10 false IL+2 5.021,4.042 5.333,4.26 0.313,0.219 10 false DIST 5.375,4.042 5.823,4.26 0.448,0.219 10 false +DP2 5.771,4.031 6.219,4.25 0.448,0.219 10 false +DP 6.146,4.031 6.438,4.229 0.292,0.198 10 false HO 6.24,4.656 6.531,4.854 0.292,0.198 10 false z4 4.427,4.667 4.719,4.865 0.292,0.198 10 false z1 4.271,5.135 4.583,5.354 0.313,0.219 10 false AU1 4.604,5.135 4.917,5.354 0.313,0.219 10 false AU2 4.938,5.135 5.25,5.354 0.313,0.219 10 false ASL 5.313,5.146 5.625,5.365 0.313,0.219 10 false EAU 5.698,5.156 6.01,5.375 0.313,0.219 10 false ECC 6.156,5.135 6.469,5.354 0.313,0.219 10 false CCS 5.771,6.073 6.083,6.292 0.313,0.219 10 false BHT 6.333,6.073 6.646,6.292 0.313,0.219 10 false EHT 5.615,6.542 5.927,6.76 0.313,0.219 10 false F20 3.875,4.146 4.115,4.365 0.24,0.219 10 false D+ 3.552,4.156 3.792,4.375 0.24,0.219 10 false D- 2.927,4.156 3.24,4.375 0.313,0.219 10 false D2+ 2.51,4.167 2.823,4.385 0.313,0.219 10 false D2- 3.906,4.75 4.146,4.969 0.24,0.219 10 false z2 2.583,4.75 2.823,4.969 0.24,0.219 10 false z3 2.719,5.167 3.031,5.385 0.313,0.219 10 false *c 3.865,5.188 4.177,5.406 0.313,0.219 10 false *b 1.552,4.25 1.865,4.469 0.313,0.219 10 false A 1.115,5.167 1.427,5.385 0.313,0.219 10 false EHT 1.854,5.156 2.167,5.375 0.313,0.219 10 false BHT 0.802,5.958 1.115,6.177 0.313,0.219 10 false EAU 1.198,5.948 1.51,6.167 0.313,0.219 10 false ECC 1.729,5.948 2.042,6.167 0.313,0.219 10 false CCS 2.24,6.021 2.552,6.24 0.313,0.219 10 false HO 2.24,6.26 2.552,6.479 0.313,0.219 10 false +DP 2.25,6.458 2.74,6.677 0.49,0.219 10 false +DP2 2.302,6.719 2.719,6.938 0.417,0.219 10 false F29 2.271,7 2.688,7.219 0.417,0.219 10 false DIST 2.271,7.208 2.688,7.427 0.417,0.219 10 false IL+2 2.24,7.417 2.656,7.635 0.417,0.219 10 false IL-2 1.74,7.427 2.052,7.646 0.313,0.219 10 false AU1 1.354,7.438 1.667,7.656 0.313,0.219 10 false AU2 0.948,7.438 1.26,7.656 0.313,0.219 10 false ASL 0.479,6.177 0.792,6.396 0.313,0.219 10 false D+ 0.479,6.427 0.719,6.646 0.24,0.219 10 false D- 0.458,6.75 0.875,6.969 0.417,0.219 10 false F30 0.479,7.177 0.792,7.396 0.313,0.219 10 false D2- 0.469,7.406 0.781,7.625 0.313,0.219 10 false D2+
*A w/o Steering Heater *B w/ Steering Heater
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Color: Light Green
*c Color: Black - -
V100144

Interlock - -


NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.



i.

Set the spiral cable sub-assembly to the center position.



ii.

Measure the resistance between each terminal of the spiral cable sub-assembly according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-1 (CCS) - z4-3 (CCS) Always 3 Ω or less
F29-2 (ECC) - z1-7 (ECC) Always 3 Ω or less
F29-2 (ECC) - z4-4 (ECC) Always 3 Ω or less
F29-3 (EAU) - z1-8 (EAU) Always 3 Ω or less
F29-4 (ASL) - z1-9 (ASL)*1 Always 3 Ω or less
F29-5 (AU2) - z1-10 (AU2) Always 3 Ω or less
F29-6 (AU1) - z1-11 (AU1) Always 3 Ω or less
F29-9 (HO) - z1-1 (HO) Always 3 Ω or less
F29-10 (+DP) - z1-2 (+DP) Always 3 Ω or less
F29-11 (+DP2) - z1-3 (+DP2) Always 3 Ω or less
F29-12 (DIST) - z1-4 (DIST) Always 3 Ω or less
F29-13 (IL+2) - z1-5 (IL+2) Always 3 Ω or less
F29-14 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
F20-2 (EHT) - A-3 (EHT)*2 Always 3 Ω or less
F20-4 (BHT) - A-4 (BHT)*2 Always 3 Ω or less
F30-1 (D+) - z2-2 (D+) Always Below 1 Ω
F30-2 (D-) - z2-1 (D-) Always Below 1 Ω
F30-3 (D2-) - z3-1 (D2-)*3 Always Below 1 Ω
F30-4 (D2+) - z3-2 (D2+)*3 Always Below 1 Ω


*1: w/ Speed Limiter System

*2: w/ Steering Heater

*3: for Dual Type



iii.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable sub-assembly 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-1 (CCS) - z4-3 (CCS) Always 3 Ω or less
F29-2 (ECC) - z1-7 (ECC) Always 3 Ω or less
F29-2 (ECC) - z4-4 (ECC) Always 3 Ω or less
F29-3 (EAU) - z1-8 (EAU) Always 3 Ω or less
F29-4 (ASL) - z1-9 (ASL)*1 Always 3 Ω or less
F29-5 (AU2) - z1-10 (AU2) Always 3 Ω or less
F29-6 (AU1) - z1-11 (AU1) Always 3 Ω or less
F29-9 (HO) - z1-1 (HO) Always 3 Ω or less
F29-10 (+DP) - z1-2 (+DP) Always 3 Ω or less
F29-11 (+DP2) - z1-3 (+DP2) Always 3 Ω or less
F29-12 (DIST) - z1-4 (DIST) Always 3 Ω or less
F29-13 (IL+2) - z1-5 (IL+2) Always 3 Ω or less
F29-14 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
F20-2 (EHT) - A-3 (EHT)*2 Always 3 Ω or less
F20-4 (BHT) - A-4 (BHT)*2 Always 3 Ω or less
F30-1 (D+) - z2-2 (D+) Always Below 1 Ω
F30-2 (D-) - z2-1 (D-) Always Below 1 Ω
F30-3 (D2-) - z3-1 (D2-)*3 Always Below 1 Ω
F30-4 (D2+) - z3-2 (D2+)*3 Always Below 1 Ω


*1: w/ Speed Limiter System

*2: w/ Steering Heater

*3: for Dual Type



iv.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-1 (CCS) - z4-3 (CCS) Always 3 Ω or less
F29-2 (ECC) - z1-7 (ECC) Always 3 Ω or less
F29-2 (ECC) - z4-4 (ECC) Always 3 Ω or less
F29-3 (EAU) - z1-8 (EAU) Always 3 Ω or less
F29-4 (ASL) - z1-9 (ASL)*1 Always 3 Ω or less
F29-5 (AU2) - z1-10 (AU2) Always 3 Ω or less
F29-6 (AU1) - z1-11 (AU1) Always 3 Ω or less
F29-9 (HO) - z1-1 (HO) Always 3 Ω or less
F29-10 (+DP) - z1-2 (+DP) Always 3 Ω or less
F29-11 (+DP2) - z1-3 (+DP2) Always 3 Ω or less
F29-12 (DIST) - z1-4 (DIST) Always 3 Ω or less
F29-13 (IL+2) - z1-5 (IL+2) Always 3 Ω or less
F29-14 (IL-2) - z1-6 (IL-2) Always 3 Ω or less
F20-2 (EHT) - A-3 (EHT)*2 Always 3 Ω or less
F20-4 (BHT) - A-4 (BHT)*2 Always 3 Ω or less
F30-1 (D+) - z2-2 (D+) Always Below 1 Ω
F30-2 (D-) - z2-1 (D-) Always Below 1 Ω
F30-3 (D2-) - z3-1 (D2-)*3 Always Below 1 Ω
F30-4 (D2+) - z3-2 (D2+)*3 Always Below 1 Ω


*1: w/ Speed Limiter System

*2: w/ Steering Heater

*3: for Dual Type


If the result is not as specified, replace the spiral cable sub-assembly.