ILLUMINATED ENTRY SYSTEM
The illuminated entry system has the following control functions:
| Control | Outline | Lights that Operate |
|---|---|---|
| Actuation Area-linked*1 | When a registered key is brought within any vehicle exterior detection area around the doors, the items listed to the right turn on. | ·
Map Light Assembly ·
No. 1 Room Light Assembly |
| Door Lock/Unlock-linked | When any door is unlocked, the lights that operate turn on. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
| When the all doors is locked, the lights that operate turn off. | ||
| Door Open/Close-linked | When any door is opened, the lights that operate turn on. | ·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 ·
Power Switch Illumination |
| When the power switch is turned on (ACC or IG) and all doors are closed, the lights that operate turn off. | ·
Map Light Assembly ·
No. 1 Room Light Assembly |
|
| Power Switch-linked | When the power switch is turned from on (ACC or IG) to off, the lights that operate turn on. | ·
Map Light Assembly ·
No. 1 Room Light Assembly |
| Shift Position-linked*2 | When the shift lever is moved from P to any other position, the lights that operate dim. | ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
| Delay | When approximately 15 seconds elapse after the following condition is met, the lights that operate turn off (*1):
·
An actuation area-linked function is used. |
·
Map Light Assembly ·
No. 1 Room Light Assembly |
| When approximately 15 seconds elapse after the following condition is met, the lights that operate turn off:
·
An power switch-linked function is used. |
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
|
| When approximately 15 seconds elapse after either of the following conditions is met, the lights that operate turn off:
·
The door unlock-linked function is active. ·
Any door is opened and then all doors are closed when the power switch is off. |
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2 |
*1: w/ Entry Function
*2: w/ Door Ambient Illumination Light
BATTERY SAVING CONTROL SYSTEM
The battery saving control system has the following control functions:
| Control | Outline | Lights that Operate |
|---|---|---|
| Basic function | When 20 minutes elapse after the power switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
|
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*1 ·
Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*1 ·
Power Switch Illumination |
| Interior light auto cut function | When 20 minutes elapse after the power switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
|
·
Map Light Assembly ·
No. 1 Room Light Assembly ·
No. 1 Luggage Compartment Light Assembly ·
Vanity Light Assembly |
*1: w/ Door Ambient Illumination Light