Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM32K0E _58 Vehicle Interior _062037 LIGHTING (INT) _0303907 LIGHTING SYSTEM D

LIGHTING (INT)  LIGHTING SYSTEM  OPERATION CHECK  


INSPECT ILLUMINATED ENTRY SYSTEM OPERATION


NOTICE:

Perform this inspection with the customize parameters at the initial settings.


HINT:

Perform this inspection with the door switch of the map light assembly on.

Lights Controlled by Illuminated Entry System
Control Condition Lights that Operate
Actuation Area-linked*1 With the power switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.
·

Map Light Assembly

·

No. 1 Room Light Assembly


Door Lock/Unlock-linked With the power switch off and all of the doors closed and locked, unlock either front door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.
·

Map Light Assembly

·

No. 1 Room Light Assembly

·

No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2

·

Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2


Door Open/Close-linked With the power switch off and all of the doors closed, open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.
·

Map Light Assembly

·

No. 1 Room Light Assembly

·

No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2

·

Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2


With the power switch off and all of the doors closed, open either front door and check that the light that operates turns on. While the light that operates is on, close all of the doors and check that the light that operates turns off after approximately 40 seconds*1. Power Switch Illumination
With the power switch on (ACC or IG), open either front door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.
·

Map Light Assembly

·

No. 1 Room Light Assembly


Power Switch-linked Turn the power switch from on (ACC or IG) to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.
·

Map Light Assembly

·

No. 1 Room Light Assembly

·

No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2

·

Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2


Shift position-linked*2 With the power switch turned on (ACC or IG), move the shift lever from P to any position and check that the lights dim. While the lights are dim, move the shift lever to P and check that the lights return to full brightness.
·

No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*2

·

Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*2



*1: w/ Entry Function

*2: w/ Door Ambient Illumination Light




INSPECT BATTERY SAVING CONTROL OPERATION


a.

The operations and conditions of this control are described below.

Control Condition Lights that Operate
Basic operation When 20 minutes elapse after the power switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

·

The power switch is turned on (ACC or IG).

·

Any door is opened and closed.

·

The luggage compartment door is opened and closed.

·

Any door is unlocked.

·

The key enters any exterior actuation area.



·

Map Light Assembly

·

No. 1 Room Light Assembly

·

Power Switch Illumination

·

No. 1 Interior Illumination Light Assembly (Door Ambient Illumination Light)*1

·

Instrument Cluster Finish Panel Garnish (Cup Holder Illumination Light)*1


Interior light auto cut operation When 20 minutes elapse after the power switch is turned from on (ACC or IG) to off and the lights that operate remain on, the lights are turned off.
HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

·

The power switch is turned on (ACC or IG).



·

Map Light Assembly

·

No. 1 Room Light Assembly

·

No. 1 Luggage Compartment Light Assembly

·

Vanity Light Assembly



*1: w/ Door Ambient Illumination Light