Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM32K0E _59 Vehicle Exterior _061789 WIPER / WASHER _0304153 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

a.

for LH Side:

i.
E356850C03
1.552,2.74 1.854,2.469 true 1.906,2.354 2.073,2.542 0.167,0.188 10 true *a 1.156,2.521 1.323,2.708 0.167,0.188 10 true A 1.156,2.833 1.323,3.021 0.167,0.188 10 true A
*a Alignment Mark


Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




b.

for RH Side:

i.
E356851C03
1.208,2.813 1.469,2.594 true 1.531,2.49 1.719,2.667 0.188,0.177 10 true *a 0.865,2.5 1.052,2.677 0.188,0.177 10 true A 0.781,2.813 0.969,2.99 0.188,0.177 10 true A
*a Alignment Mark


Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

a.

for LH Side:

i.
E356853C01
1.979,2.594 2.313,2.823 true 1.74,2.49 1.917,2.667 0.177,0.177 10 true *a 2.458,2.521 2.635,2.698 0.177,0.177 10 true A 2.542,2.813 2.719,2.99 0.177,0.177 10 true A
*a Alignment Mark


Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.




b.

for RH Side:

i.
E356852C01
1.573,2.521 1.917,2.75 true 1.344,2.396 1.51,2.573 0.167,0.177 10 true *a 2.125,2.521 2.292,2.698 0.167,0.177 10 true A 2.115,2.823 2.281,3 0.167,0.177 10 true A
*a Alignment Mark


Operate the windshield wiper motor assembly.


ii.

Stop the windshield wiper motor assembly operation.


iii.

Check the automatic stop (park) position.

HINT:

After the front wiper motor is stopped, check the automatic stop position after lifting the wiper blade 2 times.


Standard Clearance:
Area Measurement
A 7.5 mm (0.295 in.)


OK:

The front wiper stops at the position shown in the illustration.