Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH
RM32K0E _59 Vehicle Exterior _061789 WIPER / WASHER _0304157 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Rain Sensor)

a.

Check the front washer operation (for Wiper Switch RH Side Type).

i.
E257039C71
0.25,1 0.75,1.25 0.5,0.25 2.667,1 3.167,1.25 0.5,0.25 1.948,1.333 1.583,1.75 true 2.75,1.75 2.396,1.333 true 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.385,1.021 0.698,1.219 0.313,0.198 10 false F26 2.802,1.021 3.115,1.219 0.313,0.198 10 false F36 1.458,1.771 1.771,1.969 0.313,0.198 10 false WF 2.688,1.771 3,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F36-7 (WF) and a negative (-) lead to terminal F36-4 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F36-7 (WF) and F36-4 (EW).

OK:

Voltage changes as shown in the illustration.


E361233E01
4.917,1.5 4.75,1.323 false 4,1.49 4.125,1.323 false 1.646,0.198 3.792,0.396 2.146,0.198 10 false Washer Switch: 3.333,0.156 3.75,0.333 0.417,0.177 10 false On 3.333,0.448 3.667,0.667 0.333,0.219 10 false Off 2.875,0.813 3.667,1 0.792,0.188 10 false 11 to 14 V 3.302,1.135 3.667,1.333 0.365,0.198 10 false 0 V 2.281,1.396 4.427,1.594 2.146,0.198 10 false Approximately 0.5 seconds 4.979,1.396 6.719,1.646 1.74,0.25 10 false Approximately 2.2 seconds 0.271,0.833 2.667,1.229 2.396,0.396 10 false Voltage between terminals F36-7 (WF) and F36-4 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation (for Wiper Switch LH Side Type).

i.
E239385C84
0.167,1.083 0.667,1.333 0.5,0.25 2.75,1.083 3.25,1.333 0.5,0.25 0.708,1.75 0.958,1.417 true 1.438,1.417 1.688,1.75 true 0.302,1.104 0.646,1.333 0.344,0.229 10 false F39 2.875,1.104 3.229,1.333 0.354,0.229 10 false F27 0.104,0.052 0.385,0.271 0.281,0.219 10 false *a 0.604,1.76 0.885,1.958 0.281,0.198 10 false EW 1.604,1.76 1.938,1.948 0.333,0.188 10 false WF
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F39-4 (WF) and a negative (-) lead to terminal F39-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F39-4 (WF) and F39-7 (EW).

OK:

Voltage changes as shown in the illustration.


E361233E02
4.917,1.5 4.75,1.323 false 4,1.49 4.125,1.323 false 1.646,0.198 3.792,0.396 2.146,0.198 10 false Washer Switch: 3.333,0.156 3.75,0.333 0.417,0.177 10 false On 3.333,0.448 3.667,0.667 0.333,0.219 10 false Off 2.875,0.813 3.667,1 0.792,0.188 10 false 11 to 14 V 3.302,1.135 3.667,1.333 0.365,0.198 10 false 0 V 2.281,1.396 4.427,1.594 2.146,0.198 10 false Approximately 0.5 seconds 4.979,1.396 6.719,1.646 1.74,0.25 10 false Approximately 2.2 seconds 0.271,0.833 2.667,1.229 2.396,0.396 10 false Voltage between terminals F39-4 (WF) and F39-7 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Auto Wiper System)

a.

Check the front wiper intermittent operation (for Wiper Switch RH Side Type).

i.
E257039C72
0.25,1 0.75,1.25 0.5,0.25 2.667,1 3.167,1.25 0.5,0.25 1.25,1.052 0.823,0.49 true 2.688,1.719 2.354,1.344 true 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.385,1.031 0.698,1.229 0.313,0.198 10 false F26 2.802,1.031 3.115,1.229 0.313,0.198 10 false F36 0.604,0.396 0.917,0.594 0.313,0.198 10 false +1 2.76,1.625 3.073,1.823 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F26-3 (+1) and a negative (-) lead to terminal F36-4 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Check the voltage between terminals F26-3 (+1) and F36-4 (EW) with the intermittent wiper operating at different speeds.

OK:

Voltage changes as shown in the illustration.


E136493E94
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.802,1.135 1.729,0.635 10 false Voltage between terminals F26-3 (+1) and F36-4 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 0.6 to 2.6 seconds 5.792,1 7.021,1.198 1.229,0.198 10 false 5.7 to 15.7 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front wiper intermittent operation (for Wiper Switch LH Side Type).

i.
E239385C85
0.167,1.083 0.667,1.333 0.5,0.25 2.75,1 3.25,1.25 0.5,0.25 0.75,1.75 0.958,1.406 true 2.208,1.094 2.615,0.521 true 0.292,1.104 0.635,1.333 0.344,0.229 10 false F39 2.885,1.031 3.24,1.26 0.354,0.229 10 false F27 0.104,0.052 0.385,0.271 0.281,0.219 10 false *a 0.625,1.76 0.906,1.958 0.281,0.198 10 false EW 2.688,0.417 3.021,0.604 0.333,0.188 10 false +1
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F27-2 (+1) and a negative (-) lead to terminal F39-7 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Check the voltage between terminals F27-2 (+1) and F39-7 (EW) with the intermittent wiper operating at different speeds.

OK:

Voltage changes as shown in the illustration.


E136493E95
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.49 1.781,0.844 1.708,0.354 10 false Voltage between terminals F27-2 (+1) and F39-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 0.6 to 2.6 seconds 5.792,1 7.031,1.198 1.24,0.198 10 false 5.7 to 15.7 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the front washer operation (for Wiper Switch RH Side Type).

i.
E257039C73
0.25,1 0.75,1.25 0.5,0.25 2.667,1 3.167,1.25 0.5,0.25 1.958,1.333 1.667,1.667 true 2.75,1.667 2.385,1.333 true 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.385,1.031 0.698,1.229 0.313,0.198 10 false F26 2.781,1.031 3.094,1.229 0.313,0.198 10 false F36 1.521,1.677 1.833,1.875 0.313,0.198 10 false WF 2.677,1.677 2.99,1.875 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F36-7 (WF) and a negative (-) lead to terminal F36-4 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F36-7 (WF) and F36-4 (EW).

OK:

Voltage changes as shown in the following illustration.


E361233E03
4.917,1.5 4.75,1.323 false 4,1.49 4.125,1.323 false 1.646,0.198 3.792,0.396 2.146,0.198 10 false Washer Switch: 3.333,0.156 3.75,0.333 0.417,0.177 10 false On 3.333,0.448 3.667,0.667 0.333,0.219 10 false Off 2.875,0.813 3.667,1 0.792,0.188 10 false 11 to 14 V 3.302,1.135 3.667,1.333 0.365,0.198 10 false 0 V 2.281,1.396 4.427,1.594 2.146,0.198 10 false Approximately 0.5 seconds 4.979,1.396 6.719,1.646 1.74,0.25 10 false Approximately 2.2 seconds 0.271,0.833 2.667,1.229 2.396,0.396 10 false Voltage between terminals F36-7 (WF) and F36-4 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Check the front washer operation (for Wiper Switch LH Side Type).

i.
E239385C86
0.167,1.083 0.667,1.333 0.5,0.25 2.75,1.083 3.25,1.333 0.5,0.25 0.708,1.75 0.958,1.417 true 1.438,1.417 1.688,1.75 true 0.302,1.104 0.646,1.333 0.344,0.229 10 false F39 2.875,1.104 3.229,1.333 0.354,0.229 10 false F27 0.104,0.052 0.385,0.271 0.281,0.219 10 false *a 0.604,1.76 0.885,1.958 0.281,0.198 10 false EW 1.604,1.76 1.938,1.948 0.333,0.188 10 false WF
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F39-4 (WF) and a negative (-) lead to terminal F39-7 (EW).


ii.

Turn the power switch on (IG).


iii.

Turn the washer switch on and off, and check the voltage between terminals F39-4 (WF) and F39-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E361233E04
4.917,1.5 4.75,1.323 false 4,1.49 4.125,1.323 false 1.646,0.198 3.792,0.396 2.146,0.198 10 false Washer Switch: 3.333,0.156 3.75,0.333 0.417,0.177 10 false On 3.333,0.448 3.667,0.667 0.333,0.219 10 false Off 2.875,0.813 3.667,1 0.792,0.188 10 false 11 to 14 V 3.302,1.135 3.667,1.333 0.365,0.198 10 false 0 V 2.281,1.396 4.427,1.594 2.146,0.198 10 false Approximately 0.5 seconds 4.979,1.396 6.719,1.646 1.74,0.25 10 false Approximately 2.2 seconds 0.271,0.833 2.667,1.229 2.396,0.396 10 false Voltage between terminals F39-4 (WF) and F39-7 (EW):

If the result is not as specified, replace the windshield wiper switch assembly.