Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT BUMPER › 2016.10–2019.09
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304172 FRONT BUMPER A

EXTERIOR PANELS / TRIM  FRONT BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front bumper removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Front bumper assembly Change grille shutter control modes and/or perform initialization (w/Grille Shutter) Grille Shutter system (Click here)

PROCEDURE

Hide 1. PRECAUTION (w/ Grille Shutter)

a.

Change the grille shutter control mode to maintenance mode.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION

NOTICE:

Make sure to change the grille shutter control mode to maintenance mode to prevent the grill shutter from opening or closing when the power switch is off.



Hide 53141F 2.REMOVE RADIATOR COVER

a.
B454112

Remove the 5 clips and 2 hood bumper cushions.


b.
B454114

Disengage the guides to remove the radiator cover.


Hide 75602A 3.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY LH

a.
B465601

Remove the 3 screws and 2 clips.


b.
B465602C01
0.417,0.76 0.885,1.031 true 2.5,0.708 2.708,0.885 0.208,0.177 10 true *a 0.229,0.667 0.438,0.844 0.208,0.177 10 false *1
*1 Pin Hold Clip
*a 90 deg


Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

HINT:

Use the same procedure for the RH side and LH side.



c.
B465625C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull back the edge of the front fender liner LH and disengage the claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:
·

Do not apply excessive force when pulling back the front fender liner LH.

·

To avoid damaging the claws, do not forcibly pull the front fender moulding sub-assembly LH.




d.

Disengage the clips and separate the front fender moulding sub-assembly LH.


Hide 75601A 4.SEPARATE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 5.REMOVE FRONT BUMPER ASSEMBLY

a.
B454115C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the front bumper assembly.

HINT:

Use the same procedure for the RH side and LH side.



b.
B465603

Remove the 6 screws.


c.
B454116C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claws as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.



d.

w/ Fog Light:

i.
B465606C01
0.302,2.844 0.552,3.052 0.25,0.208 12 true *A 1.885,2.854 2.135,3.063 0.25,0.208 12 true *B
*A w/ Fog Light
*B w/o Fog Light
V113147

Remove in this Direction


Pull back the side of the front bumper assembly and disconnect the connector.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.


HINT:

Use the same procedure for the RH side and LH side.




e.

w/o Fog Light:

i.

Pull back the side of the front bumper assembly and disconnect the connector from the fog light cover.

NOTICE:

Do not apply excessive force when pulling back the front bumper assembly.


HINT:

Use the same procedure for the RH side and LH side.




f.

w/ Headlight Cleaner System:

i.
B454121

Disconnect the washer hose and drain the washer fluid.

HINT:

Use a container to collect the washer fluid.




g.
B454118C01
0.969,1.323 0.563,1.073 true 1.281,0.5 0.938,0.385 true 0.271,0.938 0.51,1.146 0.24,0.208 10 true *B 1.313,0.427 1.552,0.635 0.24,0.208 10 true *A
*A w/ Toyota Safety Sense
*B w/ TOYOTA Parking Assist-sensor System


w/ TOYOTA Parking Assist-sensor System:

i.

Disconnect the connector.



h.

w/ Toyota Safety Sense:

i.

Disconnect the connector.



i.
B453494

Remove the 3 bolts.


j.
B465632C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the claw to remove front bumper assembly as shown in the illustration.