When installing the name plates, heat the vehicle body, back door outside garnish and name plates using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
·
Back Door Outside Garnish ·
Name Plate |
20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the vehicle body, back door outside garnish or name plate excessively.
75443
1.INSTALL NO. 3 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 3 back door name plate.
Remove the release paper from the No. 3 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 3 back door name plate as shown in the illustration.
| *a | Reference Values | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 115.8 mm (4.56 in.) | B | 78.9 mm (3.106 in.) |
| C | 74.3 mm (2.93 in.) | D | 191.4 mm (7.54 in.) |
75374
2.INSTALL SIDE PANEL EMBLEM
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove any remaining double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the vehicle body and a new side panel emblem.
Remove the release paper from the side panel emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
for LH Side:
Install the side panel emblem as shown in the illustration.
| *a | Reference Values | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 85.5 mm (3.37 in.) | B | 42.8 mm (1.69 in.) |
| C | 62.6 mm (2.46 in.) | D | 195.5 mm (7.70 in.) |
for RH Side:
Install the side panel emblem as shown in the illustration.
| *a | Reference Values | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 90.6 mm (3.57 in.) | B | 45.9 mm (1.807 in.) |
| C | 55.8 mm (2.20 in.) | D | 190.4 mm (7.50 in.) |
75431A
3.INSTALL NO. 1 BACK DOOR EMBLEM
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 1 back door emblem.
Remove the release paper from the No. 1 back door emblem.
After removing the release paper, keep the exposed adhesive free from foreign matter.
| *a | Location Pin |
Engage the location pins and install the No. 1 back door emblem as shown in the illustration.
75441E
4.INSTALL NO. 1 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 1 back door name plate.
Remove the release paper from the No. 1 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 back door name plate as shown in the illustration.
| *a | Reference Values | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 57.0 mm (2.24 in.) | B | 85.5 mm (3.37 in.) |
| C | 83.2 mm (3.28 in.) | - | - |
75442A
5.INSTALL NO. 2 BACK DOOR NAME PLATE
Clean the back door outside garnish surface.
Using a heat light, heat the back door outside garnish surface.
Remove any remaining double-sided tape from the back door outside garnish.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the back door outside garnish and a new No. 2 back door name plate.
Remove the release paper from the No. 2 back door name plate.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 2 back door name plate as shown in the illustration.
| *a | Reference Values | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 65.1 mm (2.56 in.) | B | 113.7 mm (4.48 in.) |