Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK
RM32K0E _58 Vehicle Interior _061818 DOOR LOCK _0304544 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B450689C02
1.313,3.781 0.906,3.635 true 2.521,3.698 2.094,3.802 true 1.479,4.052 1.25,4.323 true 1.927,4.063 2.167,4.344 true 0.417,3.094 0.729,3.25 0.313,0.156 10 false *a 1.583,2.667 1.896,2.823 0.313,0.156 10 false *b 1.146,2.563 1.458,2.719 0.313,0.156 10 false *c 0.771,3.563 1.083,3.719 0.313,0.156 10 false L 2.021,4.365 2.5,4.563 0.479,0.198 10 false LSSR 2.583,3.615 2.896,3.771 0.313,0.156 10 false UL 1.167,4.354 1.479,4.51 0.313,0.156 10 false E
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) → Terminal 4 (L)
Auxiliary battery negative (-) → Terminal 1 (UL)
Locks
Auxiliary battery positive (+) → Terminal 1 (UL)
Auxiliary battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly LH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

a.
B450690C02
1.313,3.781 0.885,3.646 true 1.448,4.052 1.177,4.396 true 1.927,4.052 2.229,4.375 true 2.531,3.646 2.083,3.823 true 0.396,3.115 0.708,3.271 0.313,0.156 10 false *a 1.771,2.688 2.083,2.844 0.313,0.156 10 false *b 2.208,2.604 2.521,2.76 0.313,0.156 10 false *c 0.75,3.563 1.063,3.719 0.313,0.156 10 false L 1.125,4.417 1.438,4.573 0.313,0.156 10 false E 2.063,4.406 2.479,4.583 0.417,0.177 10 false LSSR 2.583,3.573 2.896,3.729 0.313,0.156 10 false UL
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) → Terminal 4 (L)
Auxiliary battery negative (-) → Terminal 1 (UL)
Locks
Auxiliary battery positive (+) → Terminal 1 (UL)
Auxiliary battery negative (-) → Terminal 4 (L)
Unlocks


If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.



Hide 69060A 3.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B450691C02
1.552,3.781 1.281,3.219 true 1.313,3.833 0.948,3.646 true 1.292,4.042 0.917,4.271 true 1.479,4.063 1.354,4.333 true 1.906,4.073 1.969,4.333 true 2.104,4.063 2.365,4.323 true 2.469,3.729 2.104,3.844 true 1.865,3.771 2.125,3.25 true 0.323,3.115 0.635,3.271 0.313,0.156 10 false *a 1.49,2.844 1.802,3 0.313,0.156 10 false *b 1.083,2.74 1.396,2.896 0.313,0.156 10 false *c 0.729,3.573 1.042,3.729 0.313,0.156 10 false DL 0.76,4.219 1.073,4.375 0.313,0.156 10 false E 1.188,4.354 1.667,4.552 0.479,0.198 10 false DLSR 1.958,4.354 2.271,4.51 0.313,0.156 10 false E 2.24,4.354 2.688,4.552 0.448,0.198 10 false LSSR 2.521,3.646 2.833,3.802 0.313,0.156 10 false UL 2.188,3.167 2.5,3.323 0.313,0.156 10 false L 0.885,3.146 1.375,3.333 0.49,0.188 10 false UNDL
*a Component without harness connected
(Rear Door Lock with Motor Assembly LH)
*b Unlock
*c Lock


Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the rear door lock motor and double lock motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) → Terminal 4 (DL)
Auxiliary battery negative (-) → Terminal 3 (UNDL)
Locks
Auxiliary battery positive (+) → Terminal 3 (UNDL)
Auxiliary battery negative (-) → Terminal 4 (DL)
Unlocks
Auxiliary battery positive (+) → Terminal 2 (L)
Auxiliary battery negative (-) → Terminal 1 (UL)
Sets
Auxiliary battery positive (+) → Terminal 1 (UL)
Auxiliary battery negative (-) → Terminal 2 (L)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly LH.



b.

Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (LSSR) - 6 (E) Locked 10 kΩ or higher
5 (LSSR) - 6 (E) Unlocked Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 4.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

a.
B450692C02
1.552,3.771 1.177,3.188 true 1.844,3.781 2.26,3.229 true 2.104,3.833 2.438,3.719 true 2.104,4.031 2.521,4.323 true 1.927,4.073 2.094,4.333 true 1.5,4.083 1.438,4.365 true 1.292,4.073 0.979,4.344 true 1.313,3.802 0.885,3.74 true 0.25,3.063 0.563,3.219 0.313,0.156 10 false *a 1.792,2.844 2.104,3 0.313,0.156 10 false *b 2.198,2.76 2.51,2.917 0.313,0.156 10 false *c 0.76,3.646 1.073,3.802 0.313,0.156 10 false L 0.906,4.365 1.219,4.521 0.313,0.156 10 false E 1.292,4.375 1.698,4.563 0.406,0.188 10 false LSSR 2.063,4.365 2.375,4.521 0.313,0.156 10 false E 2.49,3.635 2.938,3.792 0.448,0.156 10 false UNDL 2.344,3.156 2.656,3.313 0.313,0.156 10 false DL 0.948,3.104 1.26,3.26 0.313,0.156 10 false UL 2.375,4.365 2.813,4.573 0.438,0.208 10 false DLSR
*a Component without harness connected
(Rear Door Lock with Motor Assembly RH)
*b Unlock
*c Lock


Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the rear door lock motor and double lock motor.

OK:
Auxiliary Battery Connection Result
Auxiliary battery positive (+) → Terminal 2 (DL)
Auxiliary battery negative (-) → Terminal 1 (UNDL)
Locks
Auxiliary battery positive (+) → Terminal 1 (UNDL)
Auxiliary battery negative (-) → Terminal 2 (DL)
Unlocks
Auxiliary battery positive (+) → Terminal 4 (L)
Auxiliary battery negative (-) → Terminal 3 (UL)
Sets
Auxiliary battery positive (+) → Terminal 3 (UL)
Auxiliary battery negative (-) → Terminal 4 (L)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (LSSR) - 10 (E) Locked 10 kΩ or higher
9 (LSSR) - 10 (E) Unlocked Below 1 Ω
5 (DLSR) - 6 (E) Unset 10 kΩ or higher
5 (DLSR) - 6 (E) Set Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.