Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM32K0E _59 Vehicle Exterior _061963 MIRROR (EXT) _0304564 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87940 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

a.
B450635C03
2.125,3.604 2.625,3.125 true 2.094,3.781 2.573,4.156 true 1.906,3.781 1.438,4.115 true 1.021,2.896 1.333,3.052 0.313,0.156 10 false *a 2.646,2.906 2.958,3.063 0.313,0.156 10 false MV 2.625,4.104 2.938,4.26 0.313,0.156 10 false M+ 1.188,4.083 1.5,4.24 0.313,0.156 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror surface.

i.

Apply voltage and check the operation of the outer rear view mirror assembly LH.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 14 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 14 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 13 (MH)
Auxiliary battery negative (-) → Terminal 14 (M+)
Turns right
Auxiliary battery positive (+) → Terminal 14 (M+)
Auxiliary battery negative (-) → Terminal 13 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.
B450636C03
1.292,3.792 0.917,4.094 true 1.438,3.792 1.5,4.125 true 1.021,2.927 1.333,3.083 0.313,0.156 10 false *a 0.802,4.052 1.115,4.208 0.313,0.156 10 false + 1.5,4.156 1.813,4.313 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (+) - 9 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror LH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 8 and the negative (-) auxiliary battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror LH.



c.
B450637C03
1.354,1.344 0.938,1.74 true 1.875,1.354 2.198,1.75 true 0.302,0.198 0.615,0.354 0.313,0.156 10 false *a 0.896,1.719 1.198,1.906 0.302,0.188 10 false - 2.073,1.781 2.552,1.979 0.479,0.198 10 false BSL+
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor)

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 12 (BSL+) and a negative (-) lead to terminal 9 (-) and check that the blind spot monitor indicator comes on.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 12 (BSL+)
Auxiliary battery negative (-) → Terminal 9 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror LH.



d.
B450638C02
1.917,4 2.333,3.583 true 2.042,4.021 2.5,3.813 true 1.073,3.385 1.385,3.542 0.313,0.156 10 false *a 1.292,0.073 1.615,0.271 0.323,0.198 10 false (A) 0.948,1.01 1.271,1.208 0.323,0.198 10 false (B) 1.156,2.146 1.479,2.344 0.323,0.198 10 false (C) 1.646,2.427 1.969,2.625 0.323,0.198 10 false (D) 2.177,2.74 2.5,2.938 0.323,0.198 10 false (E) 2.396,3.479 2.719,3.635 0.323,0.156 10 false MR 2.563,3.708 2.885,3.865 0.323,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Auxiliary battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

a.
B450639C03
2.094,3.594 2.427,3.271 true 2.104,3.792 2.406,4.094 true 1.917,3.792 1.604,4.115 true 1.052,2.917 1.365,3.073 0.313,0.156 10 false *a 2.49,3.167 2.802,3.375 0.313,0.208 10 false MV 2.469,4.031 2.781,4.188 0.313,0.156 10 false M+ 1.354,4.083 1.667,4.24 0.313,0.156 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror surface.

i.

Apply voltage and check the operation of the outer rear view mirror assembly RH.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 7 (MV)
Auxiliary battery negative (-) → Terminal 14 (M+)
Turns upward
Auxiliary battery positive (+) → Terminal 14 (M+)
Auxiliary battery negative (-) → Terminal 7 (MV)
Turns downward
Auxiliary battery positive (+) → Terminal 13 (MH)
Auxiliary battery negative (-) → Terminal 14 (M+)
Turns left
Auxiliary battery positive (+) → Terminal 14 (M+)
Auxiliary battery negative (-) → Terminal 13 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.
B450640C02
1.281,3.781 0.896,4.188 true 1.479,3.792 1.708,4.188 true 1.031,2.896 1.344,3.052 0.313,0.156 10 false *a 0.802,4.188 1.115,4.344 0.313,0.156 10 false + 1.74,4.208 2.052,4.365 0.313,0.156 10 false -
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the mirror heater.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (+) - 9 (-) 25°C (77°F) 8.5 to 11.5 Ω


If the result is not as specified, check the outer mirror RH.


ii.

Connect a cable from the positive (+) auxiliary battery terminal to terminal 8 and negative (-) auxiliary battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, check the outer mirror RH.



c.
B450637C04
1.354,1.354 0.948,1.719 true 1.896,1.354 2.198,1.698 true 0.281,0.198 0.594,0.354 0.313,0.156 10 false *a 0.844,1.625 1.156,1.781 0.313,0.156 10 false - 2.25,1.635 2.74,1.844 0.49,0.208 10 false BSR+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the blind spot monitor indicator. (w/ Blind Spot Monitor)

NOTICE:

Do not apply a voltage of 6 V or higher.


i.

Check the operation of the blind spot monitor indicator.


ii.

Connect 4 dry-cell batteries (1.5 V each) in series.


iii.

Connect a positive (+) lead from the batteries to terminal 12 (BSR+) and a negative (-) lead to terminal 9 (-) and check that the blind spot monitor indicator comes on.

OK:
Auxiliary battery Connection Specified Condition
Auxiliary battery positive (+) → Terminal 12 (BSR+)
Auxiliary battery negative (-) → Terminal 9 (-)
Blind spot monitor indicator comes on


If the result is not as specified, check the outer mirror RH.



d.
B450641C02
1.917,4 2.417,3.417 true 2.063,4.021 2.49,3.635 true 1.01,3.365 1.323,3.521 0.313,0.156 10 false *a 2.188,0.063 2.51,0.292 0.323,0.229 10 false (A) 2.448,0.948 2.771,1.177 0.323,0.229 10 false (B) 2.313,2.135 2.635,2.365 0.323,0.229 10 false (C) 1.792,2.448 2.115,2.677 0.323,0.229 10 false (D) 1.333,2.74 1.656,2.969 0.323,0.229 10 false (E) 2.469,3.313 2.781,3.469 0.313,0.156 10 false MR 2.563,3.573 2.875,3.729 0.313,0.156 10 false MF
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Check the operation of the retractable mirror. (w/ Power Retract Mirror)

NOTICE:
·

Disconnect and reconnect the auxiliary battery between each mirror position check.

·

The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the auxiliary battery immediately after performing each mirror position check.



i.

Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror movement.

OK:
Auxiliary battery Connection Condition Specified Condition
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Forward position (A) Moves from (A) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Forward position (A) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Driving position (C) Moves from (C) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Driving position (C) Does not move
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Auxiliary battery positive (+) → Terminal 5 (MR)
Auxiliary battery negative (-) → Terminal 6 (MF)
Retracted position (E) Does not move
Auxiliary battery positive (+) → Terminal 6 (MF)
Auxiliary battery negative (-) → Terminal 5 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.