Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304571 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK HYBRID VEHICLE CONTROL ECU


C297329E14
5.563,1.458 5.885,1.677 0.323,0.219 4.292,1.469 4.615,1.688 0.323,0.219 2.76,1.469 3.083,1.688 0.323,0.219 1.438,1.458 1.76,1.677 0.323,0.219 1.479,1.49 1.76,1.656 0.281,0.167 10 false A49 2.802,1.5 3.083,1.667 0.281,0.167 10 false A48 4.365,1.49 4.865,1.677 0.5,0.188 10 false F2 5.635,1.479 6.042,1.646 0.406,0.167 10 false F3

HINT:

The standard voltage, resistance and waveform between each pair of the hybrid vehicle control ECU terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the hybrid vehicle control ECU terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A48-26 (DB1) - F3-4 (E12) W - W-B Shift lever position signal Power switch on (IG), shift lever in D or B 11 to 14 V
Power switch on (IG), shift lever not in D or B Below 1 V
A48-14 (DB2) - F3-4 (E12) G - W-B Shift lever position signal Power switch on (IG), shift lever in D or B 11 to 14 V
Power switch on (IG), shift lever not in D or B Below 1 V
A49-15 (STP) - F3-4 (E12) SB - W-B Stop light signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
F3-3 (BATT) - F3-4 (E12) B - W-B Constant power source Power switch off 11 to 14 V
F2-28 (CCS) - F3-4 (E12) R - W-B Cruise control main switch circuit Cruise control main switch off 10 MΩ or higher
Cruise control main switch on Below 1.5 Ω
+RES switch on 235 to 245 Ω
-SET switch on 617 to 643 Ω
CANCEL switch on 1509 to 1571 Ω
A48-28 (ST1-) - F3-4 (E12) R - W-B Stop light signal Power switch on (IG), brake pedal depressed Below 1 V
Power switch on (IG), brake pedal released 11 to 14 V
F3-4 (E12) - Body ground W-B - Body ground Ground Always Below 1 Ω


CHECK FORWARD RECOGNITION CAMERA


C367139N01
3.333,0.083 3.833,0.333 0.5,0.25 3.5,0.125 3.813,0.323 0.313,0.198 10 false R5

NOTICE:

Do not apply excessive force to the connector. If a force of 10 kg or more is applied, the connector may be broken.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-8 (BZ) - R5-10 (GND) B - W-B Pre-collision city buzzer output Power switch on (IG) buzzer not sounding 11 to 14 V
Power switch on (IG) buzzer sounding Below 1 V
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
R5-5 (CA1P) - R5-10 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
R5-11 (CA1N) - R5-10 (GND) GR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
R5-6 (CANH) - R5-10 (GND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
R5-12 (CANL) - R5-10 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
R5-3 (LKSW) - R5-10 (GND) R - W-B Steering pad switch assembly signal (distance control signal) Power switch on (IG) steering pad switch assembly (distance control switch) off 4.75 to 5.25 V
Power switch on (IG) steering pad switch assembly (distance control switch) on Below 1 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between R5-5 (CA1P) and R5-10 (GND)

·

Between R5-6 (CANH) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between R5-11 (CA1N) and R5-10 (GND)

·

Between R5-12 (CANL) and R5-10 (GND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


C367140N01
2.25,0.75 2.75,1 0.5,0.25 2.417,0.792 2.729,0.99 0.313,0.198 10 false A2

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A2-2 (CA2L) - A2-1 (SGND) GR - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-3 (CA2H) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-5 (CA1P) - A2-1 (SGND) G - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
A2-6 (CA1N) - A2-1 (SGND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 2)
A2-8 (IGB) - A2-1 (SGND) B - W-B Power source Power switch on (IG) 11 to 14 V

a.
E228691E01
2.989,1.44 3.316,1.615 0.327,0.175 10 GND

Waveform 1

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-3 (CA2H) and A2-1 (SGND)

·

Between A2-5 (CA1P) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E228688E01
2.99,1.442 3.317,1.617 0.327,0.174 10 GND

Waveform 2

i.

CAN communication signal

Item Content
Tester Connection
·

Between A2-2 (CA2L) and A2-1 (SGND)

·

Between A2-6 (CA1N) and A2-1 (SGND)


Tool Setting 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.