Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304572 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The forward recognition camera receives steering angle information from the steering angle sensor (spiral cable sub-assembly). If the forward recognition camera detects a steering angle sensor (spiral cable sub-assembly) malfunction, DTC C1A47 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A47 Steering Angle Sensor 3 seconds after the power switch is turned on (IG), a signal from the steering angle sensor (spiral cable sub-assembly) indicating that there is a steering angle sensor (spiral cable sub-assembly) malfunction is detected by the forward recognition camera for 5 seconds or more.
·

Electronically controlled brake system

·

Steering angle sensor (spiral cable sub-assembly)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:

Forward recognition camera system DTC C1A47 may be stored due to a malfunction in the electronically controlled brake system. Therefore it is necessary to check for and troubleshoot electronically controlled brake system DTCs first.


a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

B

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

B

3.REPLACE FORWARD RECOGNITION CAMERA
3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
4.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1A47 is not output A
DTC C1A47 is output B



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)