Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304572 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAE  Heater Circuit  


DESCRIPTION

The forward recognition camera controls the current supplied to the pre-collision city heater (forward recognition hood).

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAE Heater Circuit When the power switch is turned to on (IG) and one of the following conditions is met:
·

While a pre-collision city heater ON request is being sent, a short circuit malfunction is detected in the pre-collision city heater for 5 seconds or more.

·

While a pre-collision city heater ON request is not being sent, an open circuit or ground short malfunction is detected in the pre-collision city heater for 5 seconds or more.


·

Pre-collision city heater (forward recognition hood)

·

Forward recognition camera

·

Harness or connector



DTC Detection Conditions
Vehicle Condition Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Power switch on (IG) ○ ○
Malfunction Status While a pre-collision city heater ON request is being sent, a short circuit malfunction is detected in the pre-collision city heater. ○
While a pre-collision city heater ON request is not being sent, an open circuit or ground short malfunction is detected in the pre-collision city heater. ○
Detection Time 5 seconds or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

If any of the detection patterns above are met, a DTC is output.


WIRING DIAGRAM

C367191E01
0.458,1.542 1.49,1.729 1.031,0.188 10 false ECU-IG1 NO. 4 3.052,1.281 3.229,1.458 0.177,0.177 10 false 1 3.24,1.385 3.521,1.573 0.281,0.188 10 false IG1 3.708,1.385 4.052,1.573 0.344,0.188 10 false HTR 2.885,1.677 3.167,1.865 0.281,0.188 10 false R8 2.875,1.854 4.594,2.25 1.719,0.396 10 false Pre-Collision City Heater (Forward Recognition Hood) 4.094,1.292 4.271,1.469 0.177,0.177 10 false 2 4.969,1.281 5.146,1.458 0.177,0.177 10 false 1 5.146,1.375 5.49,1.563 0.344,0.188 10 false HTR 4.781,2.156 5.063,2.344 0.281,0.188 10 false R5 4.771,2.313 6.667,2.531 1.896,0.219 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

After replacing or removing/installing the forward recognition camera or windshield glass, make sure to perform forward recognition camera axis adjustment

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



PROCEDURE

1.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Clear DTCs
50002 386

b.

Set the vehicle conditions to the conditions when DTCs were detected.


c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>DTC CHECK / CLEAR

Chassis > Front Recognition Camera > Trouble Codes
50001 386

Result:
Result Proceed to
DTC C1AAE is not output A
DTC C1AAE is output B



A

B

2.CHECK PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD)
2.CHECK PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD)
a.

Disconnect the pre-collision city heater (forward recognition hood) connector.


b.
C367122C01
1.313,1.865 1.594,1.26 true 2.146,1.833 1.813,1.271 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 0.99,1.781 1.531,2.042 0.542,0.26 10 false HTR 2.24,1.781 2.656,1.979 0.417,0.198 10 false IG1
*a Component without harness connected
(Pre-collision City Heater (Forward Recognition Hood))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (IG1) - 2 (HTR) Power switch off 36.1 to 39.9 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD))

NG

REPAIR PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD))

3.CHECK HARNESS AND CONNECTOR (PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD))
a.
C367123C01
1.438,0.333 1.938,0.583 0.5,0.25 1.354,1.781 1.594,1.344 true 2.073,1.771 1.802,1.323 true 0.188,0.177 0.5,0.375 0.313,0.198 10 false *a 1.615,0.365 1.927,0.563 0.313,0.198 10 false R8 1.073,1.719 1.385,1.917 0.313,0.198 10 false IG1 2.135,1.708 2.677,1.948 0.542,0.24 10 false HTR
*a Front view of wire harness connector
(to Pre-collision City Heater (Forward Recognition Hood))


Disconnect the pre-collision city heater (forward recognition hood) connector.


b.

Disconnect the forward recognition camera connector.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Resistance Voltage:
Tester Connection Switch Condition Specified Condition
R8-1 (IG1) - Body ground Power switch on (IG) 11 to 14 V
R8-1 (IG1) - Body ground Power switch off Below 1.5 V


Standard Resistance:
Tester Connection Switch Condition Specified Condition
R8-2 (HTR) - R5-1 (HTR) Power switch off Below 1 Ω
R8-2 (HTR) or R5-1 (HTR) - Body ground Power switch off 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PRE-COLLISION CITY HEATER (FORWARD RECOGNITION HOOD))

4.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Perform Forward Recognition Camera Axis Adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


Result:
Proceed to
NEXT



NEXT

END