Home › Engine / Hybrid System › CRUISE CONTROL › ROAD SIGN ASSIST SYSTEM › 2016.10–2020.08
RM32K0E _51 Engine / Hybrid System _061336 CRUISE CONTROL _0304574 ROAD SIGN ASSIST SYSTEM C

CRUISE CONTROL  ROAD SIGN ASSIST SYSTEM  C1AAA  FCM Destination Information Uninitialized  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country specification information, DTC C1AAA is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AAA FCM Destination Information Uninitialized While the power switch is turned on (IG), the forward recognition camera cannot store the country destination information.
·

CAN communication system

·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)



HINT:

This DTC is stored when the forward recognition camera cannot store the vehicle specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.


PROCEDURE

1.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Make sure that the following conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AAA is not output A
DTC C1AAA is output B



A

B

2.REPLACE FORWARD RECOGNITION CAMERA
2.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
3.CHECK FOR DTCs (ROAD SIGN ASSIST SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Clear DTCs
50002 387

b.

Make sure that the following conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR

Body Electrical > Road Sign Assist > Trouble Codes
50001 387

Result:
Result Proceed to
DTC C1AAA is not output A
DTC C1AAA is output (for LHD) B
DTC C1AAA is output (for RHD) C



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)