If the forward recognition camera detects that the forward recognition camera axis has deviated, DTC C1AA8 is stored. Also, if Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust is not performed after installing the forward recognition camera, DTC C1AA9 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AA8 | Front Camera Module Incorrect Axial Gap | While the power switch is turned on (IG) and the road sign assist system is operating, the forward recognition camera detects forward recognition camera optical axis deviation. | ·
Forward recognition camera ·
Windshield glass |
| C1AA9 | Front Camera Module Beam Axis Not Adjusted | While the power switch is turned on (IG), the forward recognition camera detects that forward recognition camera adjustment has not been completed. | Forward recognition camera |
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
Check if the stored DTCs are current DTCs.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Current DTC C1AA8 is output | A |
| Current DTC C1AA9 is output | B |
| History DTC C1AA8 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1AA8 may be stored if the forward recognition camera optical axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or being towed | A |
| Vehicle is overloaded or being towed | B |
A
B
Check the front and rear wheel alignment (toe).
for Front Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
DTC C1AA8 may be stored if the forward recognition camera optical axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for Front Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for Rear Side: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
Make sure that the following conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA8 is not output | A |
| DTC C1AA8 is output | B |
A
B
Check the installation condition of the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>INSTALLATION
If the forward recognition camera bracket is deformed or misaligned, replace the windshield glass.
No deformation or misalignment in the forward recognition camera bracket.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the windshield glass.
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
Make sure that the following conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA8 is not output | A |
| DTC C1AA8 is output | B |
A
B
Perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
Make sure that the following conditions are met.
If the conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1AA9 is not output | A |
| DTC C1AA9 is output | B |
A
B
Check for DTCs related to the forward recognition camera.
If only history DTCs are stored, they may have been stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust was performed.
Clear the DTCs.
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT