Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2016.10–2019.09
RM32K0E _53 Suspension _061341 TIRE PRESSURE MONITORING _0304575 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  Tire Pressure Warning Light Circuit  


DESCRIPTION

If the tire pressure warning ECU and receiver detects any problems, the tire pressure warning light blinks for 1 minute then illuminates, and tire pressure monitoring is disabled at the same time. At this time, the ECU stores a DTC in memory.

Connecting terminals TC and CG of the DLC3 makes the tire pressure warning light blink to output DTCs.

The tire pressure warning ECU and receiver sends the tire pressure warning light illumination request signal to the main body ECU (multiplex network body ECU) via a direct line. The main body ECU (multiplex network body ECU) then sends the signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

C257852E54
3.531,0.781 3.927,1 0.396,0.219 10 false RDA 3.938,0.656 4.229,0.917 0.292,0.26 10 false 4 4.958,0.667 5.125,0.833 0.167,0.167 10 false 4 5.083,1.677 6.854,2.115 1.771,0.438 10 false Tire Pressure Warning ECU and Receiver 1.646,1.469 3.531,1.688 1.885,0.219 10 false Combination Meter Assembly 1.365,0.469 1.646,0.635 0.281,0.167 10 false F15 1.688,0.469 3.354,0.896 1.667,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 1.615,1.76 3.5,1.979 1.885,0.219 10 false - Tire Pressure Warning Light 0.542,2.458 2.365,2.677 1.823,0.219 10 false : CAN Communication Line 1.344,1.469 1.656,1.667 0.313,0.198 10 false F4 5.156,0.771 5.927,0.969 0.771,0.198 10 false RDA 5.073,1.5 5.844,1.698 0.771,0.198 10 false M23

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK DTC OUTPUT (B1247)

B

2.CHECK DTC OUTPUT (B1247)
a.

Clear the DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Trouble Codes
50001 203
OK:

DTC B1247 is not output.



Result:
Proceed to
OK
NG



OK

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)

NG

3.CHECK OPERATION OF TIRE PRESSURE WARNING LIGHT (ACTIVE TEST)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


f.

Check the condition of the tire pressure warning light using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Indicat. Tire Pressure Warning System Tire pressure warning light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Indicat. Tire Pressure Warning System
50004 122 57
OK:

The tire pressure warning light turns on or off in accordance with the GTS operation.



Result:
Proceed to
OK
NG



OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG