Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0304576 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren assembly sounds if either of the following conditions is met:

·

The theft deterrent system is in the alarm sounding state.

·

The theft warning siren assembly is in the armed state when the power source, ground or communication line is open.


WIRING DIAGRAM

B427498E09
0.365,0.438 1.271,0.865 0.906,0.427 10 false from Auxiliary Battery 2.073,0.615 2.969,0.813 0.896,0.198 10 false ECU-B NO. 2 3.292,1.688 4.542,2.094 1.25,0.406 10 false Theft Warning Siren Assembly 5.427,1.698 7.094,2.177 1.667,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 3.302,1.531 3.76,1.729 0.458,0.198 10 false M5 5.438,1.521 5.896,1.719 0.458,0.198 10 false F16 4.25,0.76 4.865,0.958 0.615,0.198 10 false CONT 4.729,0.646 5.188,0.844 0.458,0.198 10 false 2 5.323,0.646 5.563,0.844 0.24,0.198 10 false 18 3.208,0.458 3.531,0.667 0.323,0.208 10 false +B 3.208,1.073 3.667,1.271 0.458,0.198 10 false GND 3.021,0.927 3.479,1.125 0.458,0.198 10 false 3 3.031,0.344 3.49,0.542 0.458,0.198 10 false 1 5.563,0.646 6.177,0.844 0.615,0.198 10 false SSCL

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY HORN2)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Horn2 Theft warning siren assembly OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Security Horn2
50004 123 35
OK:

The theft warning siren assembly sounds and stops correctly when operated using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - THEFT WARNING SIREN ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - THEFT WARNING SIREN ASSEMBLY - BODY GROUND)
a.
B412484C14
1.406,0.313 1.813,0.552 0.406,0.24 1.396,1.354 1.104,1.844 true 1.885,1.354 2.302,1.865 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 1.49,0.344 1.802,0.542 0.313,0.198 10 false M5 2.146,1.875 2.583,2.063 0.438,0.188 10 false GND 0.99,1.865 1.427,2.052 0.438,0.188 10 false +B
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


Disconnect the theft warning siren assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M5-1 (+B) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
M5-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - THEFT WARNING SIREN ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - THEFT WARNING SIREN ASSEMBLY)
a.

Disconnect the F16 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the M5 theft warning siren assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-18 (SSCL) - M5-2 (CONT) Always Below 1 Ω
F16-18 (SSCL) or M5-2 (CONT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE THEFT WARNING SIREN ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE THEFT WARNING SIREN ASSEMBLY
a.

Temporarily replace the theft warning siren assembly with a new or known good one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

5.CHECK THEFT WARNING SIREN ASSEMBLY
5.CHECK THEFT WARNING SIREN ASSEMBLY
a.

Turn the power switch on (IG), then off.


b.

Set the theft deterrent system to "ARMED STATE".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION


c.

Check that the security indicator changes from illuminated to blinking.


d.

Change the theft deterrent system to "ALARM SOUNDING STATE".

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION


e.

Check that the theft warning siren assembly is sounding.

OK:

Theft warning siren assembly is sounding.



Result:
Proceed to
OK
NG



OK

END (THEFT WARNING SIREN ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)