Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0304576 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (multiplex network body ECU) transmits a signal to cause the horns to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

E352023E02
1.031,0.938 3.146,1.146 2.115,0.208 10 false to Steering Pad Switch Assembly 0.115,1.813 1.031,2.302 0.917,0.49 10 false from Auxiliary Battery 1.479,2.01 1.99,2.198 0.51,0.188 10 false HORN 2.688,2.646 3.198,2.833 0.51,0.188 10 false HORN 3.219,3.792 3.49,3.969 0.271,0.177 10 false A1 3.219,3.958 4.323,4.344 1.104,0.385 10 false Low Pitched Horn Assembly 2.375,1.729 2.583,1.906 0.208,0.177 10 false 1 3.302,1.719 3.51,1.896 0.208,0.177 10 false 2 3.302,2.24 3.51,2.417 0.208,0.177 10 false 5 2.385,2.229 2.594,2.406 0.208,0.177 10 false 3 3.51,3.333 3.719,3.51 0.208,0.177 10 false 1 4.281,1.625 4.49,1.802 0.208,0.177 10 false 27 4.281,0.75 4.49,0.927 0.208,0.177 10 false 50 5.615,1.635 5.823,1.813 0.208,0.177 10 false 28 4.271,0.969 4.625,1.177 0.354,0.208 10 false 3A 4.281,1.844 4.635,2.052 0.354,0.208 10 false 3F 5.583,1.844 5.938,2.052 0.354,0.208 10 false MB 6.552,1.958 6.906,2.167 0.354,0.208 10 false IC 5.948,1.74 6.458,1.927 0.51,0.188 10 false HORN 4.281,2.823 5.885,3.208 1.604,0.385 10 false Instrument Panel Junction Block Assembly 5.448,3.542 7.104,3.948 1.656,0.406 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.INSPECT HORNS
a.

Press the horn switch and check if the horns sound.

Result:
Result Proceed to
Horns sound A
Horns do not sound B




A

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

B

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU).


B424477C05
1.396,0.292 1.667,0.531 0.271,0.24 4.896,0.5 5.167,0.74 0.271,0.24 6.26,1.063 5.844,1.396 true 0.115,0.063 0.427,0.219 0.313,0.156 10 false *a 1.458,0.323 1.771,0.521 0.313,0.198 10 false 3F 4.927,0.531 5.24,0.729 0.313,0.198 10 false MB 5.427,1.323 5.99,1.542 0.563,0.219 10 false HORN
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3F-27 - MB-28 (HORN) Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY