SYSTEM FUNCTION
| Function | Outline |
|---|---|
| Push-button start function | When the electrical key transmitter sub-assembly is brought into the vehicle and verified, this function changes the power source or starts the hybrid control system when the power switch and brake pedal are operated.
|
| Transmitter battery saving function for key | If a switch on the electrical key transmitter sub-assembly is depressed and held, this function stops transmission of the signal after approximately 20 seconds to save transmitter battery power. |
| Transmitter battery saving mode function | ·
If the unlock switch of the electrical key transmitter sub-assembly is pressed twice while the lock switch is being pressed, the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode. ·
The entry and start system does not operate while in transmitter battery saving mode. ·
If a switch of the electrical key transmitter sub-assembly is pressed, transmitter battery saving mode will be canceled. |
| Key cancel function | Cancels the entry and start system when certain operations are performed. |
| Immobiliser function | Allows the hybrid control system to be started only by registered electrical key transmitter sub-assemblies to prevent an unauthorized hybrid control system start. |
| Automatic power off function | ·
With the shift lever in P and the power switch on (ACC) (the hybrid control system is not started and the vehicle is not moving), the power automatically turns off when the vehicle is left as is for 20 minutes or more. ·
With the shift lever in P and the power switch on (IG) (the hybrid control system is not started and the vehicle is not moving), the power automatically turns off when the vehicle is left as is for 60 minutes or more. |
DETECTION AREA
Depending on the vehicle body shape, the electrical key transmitter sub-assembly may not operate in certain locations.
Even if the electrical key transmitter sub-assembly is in the vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.
Depending on the way the electrical key transmitter sub-assembly is held, the electrical key transmitter sub-assembly may not operate properly.
The key detection area may reduce in size or the electrical key transmitter sub-assembly may not be properly detected under the following conditions:
The transmitter auxiliary battery is depleted.
There are TV towers, electric power plants, broadcasting stations, gas stations or other facilities that generate strong radio waves or electrical noise nearby.
Electronic devices such as cell phones, etc. are carried with the electrical key transmitter sub-assembly.
The electrical key transmitter sub-assembly is covered by or in contact with a metal object.
A radio wave type keyless entry system or wireless remote is operated nearby.
The electrical key transmitter sub-assembly is placed near high-voltage equipment or equipment that emits electrical noise.
The vehicle interior detection area is formed and the electrical key transmitter sub-assembly is detected when any of the following conditions are met: 1) The driver door is opened and closed, 2) the brake pedal is depressed, 3) the power switch is operated, 4) the conditions required for various warnings are met, or 5) an entry door lock operation is performed.
The vehicle interior detection area when starting the hybrid control system can be customized through a customize setting.
WARNING FUNCTION
Warning
Situation: The hybrid control system is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
There are 2 patterns for this situation.
Pattern 1:
When the hybrid control system is left running and the shift lever is in a position other than P, the driver opens the door and attempts to get out of the vehicle.
In this situation, the following control is performed:
| Reason for warning | Prevention of sudden acceleration, vehicle theft deterrent, prevention of vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (ACC) or on (IG). ·
The shift lever is in a position other than P. ·
The driver door is opened. ·
No vehicle speed is detected. |
| Warning description | ·
The buzzer in the combination meter assembly sounds continuously. ·
"Shift to P Before Exiting Vehicle" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
The power switch is turned off. ·
The shift lever is in P. ·
The driver door is closed. ·
The vehicle speed is 5 km/h (3 mph) or more. |
Pattern 2:
Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Prevention of sudden acceleration, vehicle theft deterrent, prevention of vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (ACC) or on (IG). ·
The shift lever is in a position other than P. ·
The driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
No vehicle speed is detected. |
| Warning description | ·
The buzzer in the combination meter assembly sounds continuously. ·
The wireless buzzer sounds continuously. ·
"Shift to P Before Exiting Vehicle"(A) and "Key Not Detected Check Key Location"(B) are displayed alternately on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
Warning stop conditions for (A)
·
The shift lever is in P. ·
The vehicle speed is 5 km/h (3 mph). Warning stop conditions for (B) ·
The power switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
Situation: The key reminder sounds.
There are 3 patterns for this situation.
Pattern 1:
When the shift lever is in P and the steering is unlocked, the driver opens the door and attempts to get out of the vehicle.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition
(Warning starts when condition 1 is met or condition 2 is met for 1 second) |
Condition 1
·
The power switch is on (ACC). ·
The driver door is opened. |
| Condition 2
·
The power switch is off. ·
The steering is unlocked. ·
The driver door is opened. |
|
| Warning description | ·
The buzzer in the combination meter assembly sounds continuously at short and even intervals. |
| Warning Stop Condition
(One condition is met) |
·
The power switch is turned on (IG). ·
The driver door is closed. ·
The power switch is turned off and the steering is locked. |
Pattern 2:
Under the situation of pattern 1, the driver closes the driver door and attempts to leave the vehicle while carrying the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (ACC) or on (IG). ·
The shift lever is in P. ·
The driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
No vehicle speed is detected. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
The wireless buzzer sounds 3 times. ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The power switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
Pattern 3:
Under the situation of pattern 2, the driver touches the lock sensor on the door outside handle assembly. (w/ Entry Function)
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (ACC) or on (IG). ·
The shift lever is in P. ·
The electrical key transmitter sub-assembly is not in the interior detection areas. ·
The electrical key transmitter sub-assembly is in the exterior detection areas. ·
The lock sensor is on. ·
No vehicle speed is detected. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
The wireless buzzer sounds continuously. ·
"Turn Power Off"(A) and "Key Not Detected Check Key Location"(B) are displayed alternately on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
5 seconds have elapsed after the warning started (only wireless buzzer stops). ·
Any door is opened (only wireless buzzer stops). ·
Any door is closed (only wireless buzzer stops). Warning stop conditions for (A) ·
60 seconds have elapsed after the warning started. ·
The power switch is off. ·
The shift lever is in a position other than P. ·
The vehicle speed is 5 km/h (3 mph). Warning stop conditions for (B) ·
The power switch is off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
Situation: A passenger gets out of the vehicle while carrying the electrical key transmitter sub-assembly.
When the power switch is on (ACC) or on (IG), a passenger opens a door other than the driver door and attempts to get out of the vehicle while holding the electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Preventing vehicle from becoming impossible to restart |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (ACC) or on (IG). ·
A door other than the driver door is opened → closed. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
No vehicle speed is detected. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
The wireless buzzer sounds 3 times. ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The power switch is turned off. ·
The electrical key transmitter sub-assembly is returned to the vehicle. |
Situation: The electrical key transmitter sub-assembly is not in the interior detection areas.
The driver attempts to turn the power switch on (IG) when the electrical key transmitter sub-assembly is not in the cabin, or attempts to change the power source mode by touching the electrical key transmitter sub-assembly to the power switch.
In this situation, the following control is performed:
| Reason for warning | User confusion prevention |
| Warning Start Condition
(All conditions are met) |
·
The immobiliser system is set. ·
The electrical key transmitter sub-assembly is not in the vehicle or the transmitter battery is depleted. (Interior verification failed or verification failed when the transmitter battery is depleted and the electrical key transmitter sub-assembly was touched to the power switch.) ·
There is no history of unlocking the doors using the mechanical key and no history of verification failure when the power switch is pressed. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
15 seconds have elapsed after the warning started. ·
The electrical key transmitter sub-assembly is returned to the vehicle. (Interior verification succeed or verification succeed when the transmitter battery is depleted and the electrical key transmitter sub-assembly was touched to the power switch.) ·
The driver door is opened using the door outside handle and 30 seconds have elapsed. |
Situation: The vehicle is driven without a registered electrical key transmitter sub-assembly.
In this situation, the following control is performed:
| Reason for warning | Preventing vehicle from becoming impossible to restart |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (IG). ·
Warning for when a passenger gets out of the vehicle while carrying the electrical key transmitter sub-assembly is operating. ·
The vehicle speed is 5 km/h (3 mph) or more. ·
The electrical key transmitter sub-assembly is not in the vehicle. |
| Warning description | ·
The buzzer in the combination meter assembly sounds nine times. ·
"Key Not Detected Check Key Location" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The electrical key transmitter sub-assembly is returned to the vehicle. ·
The power switch is turned off. |
Situation: The electrical key transmitter sub-assembly is left in the vehicle. (w/ Entry Function)
The lock sensor on a door outside handle assembly is touched to perform an entry lock operation with the electrical key transmitter sub-assembly left in the vehicle.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition
(All conditions are met) |
·
The power switch is off. ·
All doors are closed. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
The lock sensor on a door outside handle assembly is on (touched). ·
Any door is unlocked. ·
No vehicle speed is detected. |
| Warning description | ·
The wireless buzzer sounds continuously. ·
"Key Detected in Vehicle" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
5 seconds have elapsed after the wireless buzzer is activated (only wireless buzzer stops). ·
The power switch is on (ACC) or on (IG). ·
The vehicle speed is 5 km/h (3 mph) or more. ·
Any door is opened (only wireless buzzer stops). ·
The doors are locked. ·
60 seconds have elapsed after the warning started. |
Situation: Door is ajar.
Press the lock switch on the electrical key transmitter sub-assembly or the lock sensor on a door outside handle assembly is touched to perform an entry lock operation*1 with a door open.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition
(All conditions are met) |
·
The power switch is off. ·
Any door other than the door that locked using the entry lock function is open. ·
The lock sensor is on*1 or lock switch is pressed on the electrical key transmitter sub-assembly. ·
The electrical key transmitter sub-assembly is in the exterior detection areas. |
| Warning description | ·
The wireless buzzer sounds continuously. |
| Warning Stop Condition
(One condition is met) |
·
5 seconds have elapsed after the wireless buzzer is activated. ·
The power switch is on (ACC) or on (IG). ·
All doors are closed. ·
The doors are unlocked by a wireless door unlock operation. ·
The doors are unlocked by a the entry unlock operation.*1 ·
Any of the doors are opened. |
*1: w/ Entry Function
Situation: The electrical key transmitter sub-assembly is locked inside the vehicle.
The electrical key transmitter sub-assembly is locked inside the vehicle.
In this situation, the following control is performed:
| Reason for warning | Vehicle theft deterrent |
| Warning Start Condition | Condition 1 (All conditions are met)
·
With a door open, the lock knob is locked and then the door is closed with the door handle being pulled. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
No vehicle speed is detected. |
| Condition 2 (All conditions are met)*1
·
The power switch is off. ·
All doors are closed and locked. ·
Lock operation other than entry lock operation is performed. ·
The electrical key transmitter sub-assembly is inside vehicle (matching code is detected in vehicle interior). |
|
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
The wireless buzzer sounds continuously. ·
"Key Detected in Vehicle" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
5 seconds have elapsed after the wireless buzzer is activated (only wireless buzzer stops). ·
60 seconds have elapsed after the warning started. ·
The power source mode is changed to a mode other than off. ·
Any door is opened (only wireless buzzer stops). ·
The doors are locked. ·
The vehicle speed is 5 km/h (3 mph) or more. |
*1: w/ Double Locking System
Situation: The transmitter battery is weak.
The vehicle is driven using an electrical key transmitter sub-assembly that has a low transmitter battery.
In this situation, the following control is performed:
| Reason for warning | Preventing vehicle from becoming impossible to restart, usability function |
| Warning Start Condition
(Either Condition 1 or 2 is met) |
Condition 1 (All conditions are met)
·
The power switch is turned off after being left on (IG) for more than 20 minutes. ·
The transmitter battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
No vehicle speed is detected. |
| Condition 2 (All conditions are met)
·
The hybrid control system is off → the hybrid control system is started ·
The transmitter battery voltage is low. ·
The electrical key transmitter sub-assembly is in the vehicle. ·
No vehicle speed is detected. ·
Condition 1 has been met. (In the past) |
|
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Key Battery Low Replace Key Battery" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
15 seconds have elapsed after the warning started. ·
The vehicle speed is 5 km/h (3 mph) or more. |
Situation: The steering cannot be released.
The steering cannot be released, thus the hybrid control system is prevented from starting.
The shift lever is moved to a position other than P before the steering is unlocked.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition | ·
Steering cannot be unlocked (judged by the steering lock ECU (steering lock actuator or upper bracket assembly)). |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Push POWER Switch while Turning The Steering Wheel in Either Direction" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
15 seconds have elapsed after the warning started. ·
The steering is unlocked. |
Situation: The entry and start system is malfunctioning.
An IG circuit malfunction, malfunction that interferes with the steering lock ECU (steering lock actuator or upper bracket assembly) or a vehicle speed signal malfunction is detected.
In this situation, the following control is performed:
| Reason for warning | Malfunction detection |
| Warning Start Condition
(One condition is met) |
·
The steering lock ECU (steering lock actuator or upper bracket assembly), certification ECU (smart key ECU assembly) or unlock detection switch is malfunctioning. ·
The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning. ·
An IG relay output circuit malfunction occurs three times or more consecutively. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Entry & Start System Malfunction See Owner's Manual" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
15 seconds have elapsed after the warning started. ·
The system returns to normal. |
Situation: The hybrid control system does not start. (Situation A)
When the driver door is opened using the mechanical key and the power switch is pressed, the electrical key transmitter sub-assembly cannot be detected in the vehicle, or when the power switch is pressed, the electrical key transmitter sub-assembly cannot be detected two times in a row.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(One condition is met) |
·
The immobiliser system is set. ·
The electrical key transmitter sub-assembly is not in the vehicle. ·
Key code verification error occurs when the power switch is pressed twice or the driver door key-linked unlock operation is performed. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Depress Brake Pedal and Touch POWER Switch with Key" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
60 seconds have elapsed after the warning started. ·
The electrical key transmitter sub-assembly is in the vehicle. (Interior verification succeed or verification succeed when the transmitter battery is depleted and the electrical key transmitter sub-assembly was touched to the power switch.) ·
The driver door is opened using the front door outside handle assembly (for driver door) and 30 seconds have elapsed. |
Situation: Immobiliser system certification completion occurs.
When the transmitter battery is depleted, the entry and start system is canceled or wave interference occurs, the electrical key transmitter sub-assembly is touched to the power switch.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition | ·
Electrical key transmitter sub-assembly certification result is OK. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Depress Brake Pedal & Push POWER Switch to Start" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
10 seconds have elapsed after the warning started. ·
The electrical key transmitter sub-assembly is detected by the vehicle. ·
The hybrid control system started. ·
The vehicle can be driven. ·
The immobiliser system is set and key recognition is stopped or the key cannot be recognized. |
Situation: The hybrid control system does not start. (Situation B)
There are two patterns for this situation.
Pattern 1:
The hybrid control system might be started (when the driver gets in the vehicle, or the power switch is turned on (ACC)).
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(Either condition is met) |
·
After the doors are unlocked from outside the vehicle with the power switch off, the driver door is opened. ·
With the brake pedal not depressed, the power switch is turned on (ACC). |
| Warning description
(Not displayed while the opening image is displayed.) |
·
"Depress Brake Pedal & Push POWER Switch to Start" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
19 seconds have elapsed after the warning started. ·
The hybrid control system is started. ·
The doors are locked from outside the vehicle. ·
The doors are locked by a wireless door lock operation from inside the vehicle. |
Pattern 2:
The hybrid control system might be started (when the power switch is on (IG)).
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(Either condition is met) |
·
With the brake pedal not depressed, the power switch is turned on (IG) (the hybrid control system is not started). ·
The power switch is on (IG) (the hybrid control system is not started) and the shift lever is moved from a position other than P to P. |
| Warning description | ·
"Not Ready to Drive Depress Brake Pedal & Push POWER Switch to Start" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
The power source mode is changed to any mode other than on (IG). ·
The vehicle speed is 5 km/h (3 mph) or more. ·
The shift lever is moved to a position other than P or N. |
Situation: The power switch cannot be turned off.
There are 2 patterns for this situation.
Pattern 1:
A warning message appears on the multi-information display when the driver attempts to turn the power switch off with the shift lever in any position other than P
In this situation, the following control is performed:
| Reason for warning | Prevention of auxiliary battery discharge, prevention of vehicle roll-away |
| Warning Start Condition | ·
The power switch is turned off with the shift lever in a position other than P or N. (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.) |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Shift to P Before Exiting Vehicle" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The shift lever is moved to P. ·
The power source mode is changed to a mode other than on (ACC). |
Pattern 2:
Under the situation of pattern 1, the shift lever is moved to P.
In this situation, the following control is performed:
| Reason for warning | Prevention of auxiliary battery discharge |
| Warning Start Condition | ·
The shift lever is moved to P. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Turn Power Off" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
The power source mode is changed to a mode other than on (ACC). ·
The shift lever is in any position other than P. |
Situation: Auto power off operation occurs.
A warning message appears on the multi-information display when an automatic power off operation occurs.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(All conditions are met) |
·
The shift lever is in P. ·
The power switch is on (ACC) or on (IG). ·
No vehicle speed is detected and the hybrid control system is stopped. ·
The power source mode is changed to off by automatic power off function. (20 minutes have elapsed with the power switch on (ACC) or 1 hour has elapsed with the power switch on (IG).) |
| Warning description | ·
"Auto Power Off to Conserve Battery" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(Either condition is met) |
·
10 seconds have elapsed after the warning started. ·
The power switch is turned on (ACC) or on (IG). |
Situation: An electrical key transmitter sub-assembly has been registered.
A warning message appears on the multi-information display when an electrical key transmitter sub-assembly has been registered to the vehicle.
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(All conditions are met) |
·
The power switch is off. ·
The driver door is unlocked and opened. ·
Within 10 days after a new key has been registered. |
| Warning description | ·
"A New Key has been Registered Contact Your Dealer for Details" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
60 seconds have elapsed after the warning started. ·
All doors are closed and locked. ·
The power switch is on (IG). |
Situation: The shift lever is in a position other than P or N with the hybrid control system stopped.
There are 2 patterns for this situation.
Pattern 1:
A warning message appears on the multi-information display when the shift lever is in a position other than P or N while the power switch is on (ACC) or on (IG) and the hybrid control system is stopped.
In this situation, the following control is performed:
| Reason for warning | Prevention of vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (IG). ·
No vehicle speed is detected. ·
The shift lever is in a position other than P or N. |
| Warning description | ·
The buzzer in the combination meter assembly sounds once. ·
"Hybrid System Stopped Shift to P" is displayed on the multiinformationdisplay in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
The shift lever is moved to P or N. ·
The power switch is turned off. ·
The vehicle speed is 5 km/h (3 mph) or more. |
Pattern 2:
A warning message appears on the multi-information display when the shift lever is moved to N while the hybrid control system is stopped and the power switch is on (IG).
In this situation, the following control is performed:
| Reason for warning | Usability function |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (IG). ·
The vehicle speed is detected. ·
The hybrid control system is ready to be started. ·
The shift lever is moved to N. |
| Warning description | ·
"Shift to P Position to Start" is displayed on the mult-iinformation display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
The power switch is turned off, on (ACC) or on (READY). ·
The vehicle speed is 5 km/h (3 mph) or more. ·
The hybrid control system is not ready to be started. ·
The shift lever is moved to a position other than N. |
Situation: The vehicle is moving with the power switch on (IG) and the hybrid control system is stopped.
A warning message appears on the multi-information display if the vehicle begins moving when the power switch is on (IG) and the hybrid control system is stopped.
In this situation, the following control is performed:
| Reason for warning | Prevention of vehicle roll-away |
| Warning Start Condition
(All conditions are met) |
·
The power switch is on (IG). ·
The shift lever is in a position other than P or N. ·
The hybrid control system is stopped. ·
The vehicle speed is 2 km/h (1 mph) or more. |
| Warning description | ·
The buzzer in the combination meter assembly sounds continuously. ·
"Hybrid System Stopped Stop in a Safe Place" is displayed on the multi-information display in the combination meter assembly. |
| Warning Stop Condition
(One condition is met) |
·
The shift lever is moved to N. ·
The power switch is turned off. ·
The hybrid control system is started. ·
No vehicle speed is detected. |