Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM32K0E _58 Vehicle Interior _061197 THEFT DETERRENT / KEYLESS ENTRY _0303649 ENTRY AND START SYSTEM(for Start Function) D

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  OPERATION CHECK  


OPERATION DESCRIPTION


NOTICE:

Make sure that the entry and start system (for Start Function) has not been canceled before performing this inspection.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS


a.

Push-button start function:

i.

When the electrical key transmitter sub-assembly is in a vehicle interior detection area and the brake pedal is depressed, the hybrid control system is started by pressing the power switch.


ii.

When the electrical key transmitter sub-assembly is in a vehicle interior detection area and the brake pedal is not depressed, the power source mode is changed by pressing the power switch. The power source mode changes in the following order every time the power switch is pressed: off → on (ACC) → on (IG) → off.


iii.
E352003C04
0.104,0.104 0.417,0.26 0.313,0.156 10 false *a
*a "ACCESSORY" Display


After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed while not depressing the brake pedal, the power source mode will change to on (ACC) and "ACCESSORY" will be displayed on the multi-information display.


iv.
E352004C05
0.104,0.094 0.417,0.25 0.313,0.156 10 false *a
*a "IGNITION ON" Display


After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the power switch is pressed 2 times without depressing the brake pedal, the power source mode will change to on (IG) and "IGNITION ON" will be displayed on the multi-information display.


v.
E362386C01
0.115,0.083 0.427,0.24 0.313,0.156 10 false *a
*a Key Indicator Display


After getting into the vehicle while carrying the electrical key transmitter sub-assembly when the power switch is off, if the brake pedal is depressed while the shift lever is in P, the key indicator display will be displayed on the multi-information display.


vi.

The hybrid control system will start if the power switch is pressed when the key indicator display is displayed.



b.

Changing the power source mode when the electrical key transmitter sub-assembly is not operating correctly due to wave interference or transmitter battery depletion:

i.

Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.


ii.

While depressing the brake pedal and facing the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the electrical key transmitter sub-assembly near the power switch.


iii.
E352004C06
0.104,0.094 0.417,0.25 0.313,0.156 10 false *a
*a "IGNITION ON" Display


A buzzer in the combination meter assembly will sound and the power source mode will change to on (IG) and "IGNITION ON" will be displayed on the multi-information display.


iv.

Pressing the power switch without depressing the brake pedal changes the power source mode from on (IG) to off.



c.

Starting the hybrid control system when the electrical key transmitter sub-assembly does not operate correctly due to wave interference or transmitter battery depletion:

i.

Unlock the door using the built-in mechanical key and get into the vehicle while carrying the electrical key transmitter sub-assembly.


ii.

While depressing the brake pedal with the shift lever in P and facing the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the electrical key transmitter sub-assembly near the power switch.


iii.
E362386C01
0.115,0.083 0.427,0.24 0.313,0.156 10 false *a
*a Key Indicator Display


A buzzer in the combination meter assembly will sound, the power source mode will change to on (IG) and the key indicator display will be displayed on the multi-information display.


iv.

Press the power switch with the brake pedal depressed to start the hybrid control system.




CHECK PUSH-BUTTON START FUNCTION


a.

Check the push-button start function:

i.
E362386C01
0.115,0.083 0.427,0.24 0.313,0.156 10 false *a
*a Key Indicator Display


Get into the vehicle while carrying the electrical key transmitter sub-assembly with the power switch off. With the shift lever in P, check that the key indicator display is displayed when the brake pedal is depressed. Check that the hybrid control system starts when the power switch is pressed after the key indicator display is displayed on the multi-information display.


ii.

While carrying the electrical key transmitter sub-assembly, check that the power source mode changes in the following order when the power switch is pressed with the brake pedal released: off → on (ACC) → on (IG) → off.

HINT:

If the power switch is pressed with the power switch on (IG) and the shift lever not in P, the power source mode will not change to off, but to on (ACC).



iii.

With the shift lever in P, check that the steering lock operates when a door is opened.

HINT:

When the power switch is pressed after the vehicle is stopped, the hybrid control system will stop and all power will turn off. However, if the shift lever is not in P when the power switch is pressed with the vehicle stopped, the power source mode will not change to off, but to on (ACC).



iv.
E351995C06
0.573,0.708 2.656,0.281 2.656,0.281 1.938,0.698 true 2.719,0.177 3.031,0.333 0.313,0.156 10 false *a
*a Inspection Point


Check the push-button start function operation range for the front side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION

·

Perform this inspection for both inspection points.




v.
E351996C06
0.573,0.552 2.531,0.188 2.531,0.188 1.906,0.563 true 2.594,0.094 2.906,0.25 0.313,0.156 10 false *a
*a Inspection Point


Check the push-button start function operation range for the rear side. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 2 indoor electrical key antenna assembly (rear floor).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION

·

Perform this inspection for both inspection points.




vi.
E351998C06
1.24,1.75 2.479,0.313 2.479,0.313 1.854,1.219 true 2.531,0.219 2.844,0.375 0.313,0.156 10 false *a
*a Inspection Point


Check the push-button start function operation range for the luggage compartment. Place the electrical key transmitter sub-assembly at either inspection point so that it is facing the direction shown in the illustration, and then check that the hybrid control system can be started.

NOTICE:

Even if the electrical key transmitter sub-assembly is in a vehicle interior detection area, it may not be properly detected if it is on the instrument panel, in the glove box or on the floor.


HINT:
·

Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the center of the No. 3 indoor electrical key antenna assembly (inside luggage compartment).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>PARTS LOCATION

·

Perform this inspection for both inspection points.






KEY DIAGNOSTIC MODE (Using GTS)


HINT:

The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*6. For "Overhead + Rear Room"*6, the buzzer sounds in one long, continuous beep.


HINT:
·

With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.

·

If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.



a.

Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check (Key Diag Mode).

Body Electrical > Entry&Start > Utility
Tester Display
Communication Check(Key Diag Mode)
50005 125 143

b.

Inspect the appropriate item according to the following table.

Tester Display Inspection Item
[CH1/CH2] Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) (for driver door)*8
[CH1] Overhead + Driver Side*1
[CH2] Overhead + Driver Side*1
[CH1/CH2] Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) (for front passenger door)*8
[CH1] Overhead + Passenger Side*2
[CH2] Overhead + Passenger Side*2
[CH1/CH2] Overhead + Front Room*3 No. 1 indoor electrical key antenna assembly (front floor)
[CH1] Overhead + Front Room*3
[CH2] Overhead + Front Room*3
[CH1/CH2] Overhead + Rear Room*4 No. 2 indoor electrical key antenna assembly (rear floor)
[CH1] Overhead + Rear Room*4
[CH2] Overhead + Rear Room*4
[CH1/CH2] Overhead + Back Door*5 Electrical key antenna (outside luggage compartment)*8
[CH1] Overhead + Back Door*5
[CH2] Overhead + Back Door*5
[CH1/CH2] Luggage + Back Door (inside)*6 No. 3 indoor electrical key antenna assembly (inside luggage)
[CH1] Luggage + Back Door (inside)*6
[CH2] Luggage + Back Door (inside)*6
[CH1/CH2] Immobiliser Amp*7 Amplifier (power switch)
[CH1] Immobiliser Amp*7
[CH2] Immobiliser Amp*7

·

[CH1]: Channel 1 is set.

·

[CH2]: Channel 2 is set.

·

[CH1/CH2]: Channel 1 and 2 switch automatically at a specific interval*.

*: If the electrical key transmitter sub-assembly is detected with either channel 1 or 2, the buzzer sounds.

·

*8: w/ Entry Function



c.

Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless buzzer sounds.

i.
E351993C03
0.083,0.094 0.344,0.323 0.26,0.229 12 false *A 0.094,2.646 0.344,2.875 0.25,0.229 12 false *B 2.229,1.635 2.406,1.823 0.177,0.188 10 false *a 1.292,3.698 1.469,3.885 0.177,0.188 10 false *a
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)


*1: Front door outside handle assembly (for driver door) (w/ Entry Function)

HINT:
·

Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

·

*2: Perform the same inspection for the front passenger door.





d.
E351995C01
0.573,0.708 2.656,0.281 2.656,0.281 1.938,0.698 true 2.719,0.177 3.031,0.333 0.313,0.156 10 false *a
*a Inspection Point


*3: No. 1 indoor electrical key antenna assembly (front floor)

HINT:

Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.



e.
E351996C01
0.573,0.552 2.531,0.188 2.531,0.188 1.906,0.563 true 2.594,0.094 2.906,0.25 0.313,0.156 10 false *a
*a Inspection Point


*4: No. 2 indoor electrical key antenna assembly (rear floor)

HINT:

Place the electrical key transmitter sub-assembly on the rear seat cushion.



f.
E351997C01
1.771,1.354 2.083,1.51 0.313,0.156 10 false *a
*a 0.7 to 1 m (2.30 to 3.28 ft.)


*5: Electrical key antenna (outside luggage compartment)

HINT:

Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle as shown in the illustration.



g.
E351998C01
1.24,1.75 2.479,0.313 2.479,0.313 1.854,1.219 true 2.531,0.219 2.844,0.375 0.313,0.156 10 false *a
*a Inspection Point


*6: No. 3 indoor electrical key antenna assembly (inside luggage compartment) (w/ Entry Function)

HINT:

Place the electrical key transmitter sub-assembly on the luggage room floor.



h.
E362385C01
0.5,0.438 0.927,0.688 false 2.49,0.792 2.917,1.042 false 0.271,0.313 0.583,0.51 0.313,0.198 10 false *1 3,1.01 3.313,1.208 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


*7: Amplifier (power switch)

HINT:

While facing the logo side of the electrical key transmitter sub-assembly toward the power switch, hold the transmitter near the power switch.




CHECK TRANSMITTER BATTERY SAVING MODE FUNCTION


a.

Check the transmitter battery saving mode function:

i.

Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.


ii.

Check that the entry and start system (for Start Function) does not operate while in transmitter battery saving mode.

HINT:

To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.





CHECK POWER SOURCE MODE CHANGING FUNCTION


a.

Check the power switch.

i.

Check that the power source mode changes according to the chart below.

Shift Position Brake Pedal Power Source Mode when Power Switch Pressed
P Released Off → on (ACC) → on (IG) → off
P Released On (READY) → off
P Released On (ACC)* → off
P Depressed Off → on (READY)
P Depressed On (ACC) → on (READY)
P Depressed On (IG) → on (READY)
P Depressed On (READY) → off
P Depressed On (ACC)* → off
Not P Released Off → on (ACC) → on (IG) (after power source mode changes to on (IG), power source mode changes between on (IG) and on (ACC) every time power switch is pressed)
Not P Released On (READY) → on (ACC)
Not P Depressed Off → on (IG)
Not P Depressed On (ACC) → on (IG)
Not P Depressed On (READY) → on (ACC)

HINT:

*: This situation is only applicable when the power source mode has changed from on (IG) to on (ACC). (Excluding an emergency stop by pressing the power switch 3 times quickly or pressing and holding the power switch for 2 seconds or more.)





CHECK POWER SOURCE MODE INDICATION


a.

Check the key indicator display.

E362387C01
0.688,1.031 1,1.229 0.313,0.198 10 false *a 0.708,2.365 1.021,2.563 0.313,0.198 10 false *b 4.5,0.542 4.813,0.74 0.313,0.198 10 false *c
*a "ACCESSORY" Display *b "IGNITION ON" Display
*c Key Indicator Display - -


Multi-information Display Inspection
Power Source Mode Multi-information Display
Off
(Excluding conditions in which the hybrid control system can be started)
Off
On (ACC)
(Excluding conditions in which the hybrid control system can be started)
"ACCESSORY" displayed
On (IG)
(Excluding conditions in which the hybrid control system can be started)
"IGNITION ON" displayed
Condition in which hybrid control system can be started*1 Key Indicator displayed
Hybrid control system started Off

HINT:

*1: Indicates the conditions in which the hybrid control system can be started by pressing the power switch while either of the following conditions is met:

·

Condition 1

All of the following conditions are met:

-

The power source mode was changed from on (IG) to on (ACC).

-

Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

-

The shift lever is in N and the steering is unlocked.

-

The stop light switch assembly is on.


·

Condition 2

All of the following conditions are met:

-

The power source mode was not changed from on (IG) to on (ACC).

-

Key verification is OK*2 or immobiliser is unset (power switch is on (ACC) or on (IG)).

-

The stop light switch assembly is on.

-

The shift lever is in P, or the shift lever is in N with the steering unlocked.



*2: When the electrical key transmitter sub-assembly is in the cabin, the ID code sent as a result of communication between the electrical key transmitter sub-assembly and certification ECU (smart key ECU assembly) and the ID code calculated by the certification ECU (smart key ECU assembly) are compared. If the ID codes match each other, the vehicle recognizes that the electrical key transmitter sub-assembly is in the cabin.