CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Disconnect the M67 and F1 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| M67-25 (STP1) - Body ground | Input | BE - Body ground | Stop light switch signal | Brake pedal depressed → Brake pedal released | 9 V or higher → 1 V or less | Stop Light Switch1 |
| F1-4 (+B) - F1-18 (E) | Input | L - W-B | Power source | Power switch off | 11 to 14 V | - |
| F1-22 (P) - F1-18 (E) | Input | L - W-B | P position signal | Shift lever in P → Shift lever not in P | 30 kΩ or higher → Below 200 Ω | Shift P Signal |
| F1-18 (E) - Body ground | - | W-B - Body ground | GND | Always | Below 1 Ω | - |
| F1-21 (SSW2) - Body ground | Input | GR - Body ground | SSW2 contact signal
|
Power switch pushed → Power switch not pushed | Below 15 Ω → 10 kΩ or higher | Start Switch2 |
| F1-23 (SSW1) - Body ground | Input | W - Body ground | SSW1 contact signal | Power switch pushed → Power switch not pushed | Below 15 Ω → 10 kΩ or higher | Start Switch1 |
| F1-16 (ACCD) - Body ground | Output | LG - Body ground | ACC signal | 20°C (68°F) | 285.71 to 428.57 Ω | ACC Relay Monitor |
| F1-17 (IG1D) - Body ground | Output | GR - Body ground | IG signal | 20°C (68°F) | 60.78 to 89.11 Ω | IG Relay Monitor (Outside) |
| F1-19 (SPD) - Body ground | Input | V - Body ground | Vehicle speed signal | Always | 30 kΩ or higher | Vehicle Speed Signal |
Reconnect the M67 and F1 certification ECU (smart key ECU assembly) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Input/Output | Wiring Color | Terminal Description | Condition | Specified Condition | Related Data List Item |
|---|---|---|---|---|---|---|
| M67-25 (STP1) - F1-18 (E) | Input | BE - W-B | Stop light switch signal | Brake pedal released → Brake pedal depressed | 1 V or less → 9 V or higher | Stop Light Switch1 |
| F1-14 (SLP) - F1-18 (E) | Input | G - W-B | Steering lock position signal | Steering locked → Steering unlocked | 11 to 14 V → 1.5 V or less | Steering Unlock Switch |
| F1-25 (SLR+) - F1-18 (E) | Output | P - W-B | Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly)) |
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·
The steering is unlocked. ·
The power switch is off. ·
The shift lever is in P. |
Pulse generation
(See waveform 1) |
- |
| F1-22 (P) - F1-18 (E) | Input | L - W-B | P position signal | Shift lever in P → Shift lever not in P | 9 V or higher → 2.76 V or less | Shift P Signal |
| F1-21 (SSW2) - F1-18 (E) | Input | GR - W-B | SSW2 contact signal
|
Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch2 |
| F1-23 (SSW1) - F1-18 (E) | Input | W - W-B | SSW1 contact signal | Power switch not pushed → Power switch pushed | 9 V or higher → 1 V or less | Start Switch1 |
| F1-16 (ACCD) - F1-18 (E) | Output | LG - W-B | ACC signal | Power switch off → Power switch on (ACC) | 1 V or less → 8.5 V or higher | ACC Relay Monitor |
| F1-17 (IG1D) - F1-18 (E) | Output | GR - W-B | IG signal | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher | IG Relay Monitor (Outside) |
| F1-19 (SPD) - F1-18 (E) | Input | V - W-B | Vehicle speed signal | Vehicle being driven at approx. 5 km/h (3 mph) | Pulse generation
(See waveform 2) |
Vehicle Speed Signal |
| F1-27 (ST2) - F1-18 (E) | Output | B - W-B | STSW signal | With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released | 8.5 V or higher → 1 V or less | - |
| F1-3 (IGB) - F1-18 (E) | Output | V - W-B | IGB signal | Power switch off → Power switch on (IG) | 1 V or less → 8.5 V or higher | IGB Request |
| F1-8 (CLG5) - F1-18 (E) | Output | G - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Front Room (key diagnostic mode) |
| F1-9 (CG5B) - F1-18 (E) | Output | R - W-B | Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Front Room (key diagnostic mode) |
| M67-5 (CLG6) - F1-18 (E) | Output | SB - W-B | Output to No. 2 indoor electrical key antenna assembly (rear floor) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Rear Room (key diagnostic mode) |
| M67-6 (CG6B) - F1-18 (E) | Output | BR - W-B | Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG6 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Rear Room (key diagnostic mode) |
| M67-11 (CLG7) - F1-18 (E) | Output | B - W-B | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Back Door (inside) (key diagnostic mode) |
| M67-10 (CG7B) - F1-18 (E) | Output | W - W-B | Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
Pulse generation
(See waveform 3) |
Overhead + Back Door (inside) (key diagnostic mode) |
The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.
The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:
To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the power switch on (ACC) or on (IG).
To lock the steering, open a door with the power switch off and the shift lever in P.
Using an oscilloscope, check the waveform of the ECU.
The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| *a | Steering lock motor not operating |
| *b | Steering lock motor operating |
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | F1-25 (SLR+) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Steering lock motor stopped → Steering lock motor operating → Steering lock motor stopped |
Waveform 2
| Item | Content |
|---|---|
| Tester Connection | F1-19 (SPD) - F1-18 (E) |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Vehicle being driven at approx. 5 km/h (3 mph) |
The wavelength becomes shorter as the vehicle speed increases.
| *a | For 30 seconds after any door closed |
| *b | After 30 seconds or more have elapsed since any door closed |
Waveform 3
| Item | Content |
|---|---|
| Tester Connection | F1-8 (CLG5) - F1-18 (E)
F1-9 (CG5B) - F1-18 (E) M67-5 (CLG6) - F1-18 (E) M67-6 (CG6B) - F1-18 (E) M67-11 (CLG7) - F1-18 (E) M67-10 (CG7B) - F1-18 (E) |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Procedure:
1.
Power switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Within 30 seconds of closing any door |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>TERMINALS OF ECU
CHECK ID CODE BOX (IMMOBILISER CODE ECU)
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>TERMINALS OF ECU
CHECK HYBRID VEHICLE CONTROL ECU
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>TERMINALS OF ECU
CHECK POWER SWITCH
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM>TERMINALS OF ECU