Home › General › MAINTENANCE › REAR DISC BRAKE PAD › 2016.10–2019.09
RM32K0E _V1 General _059911 MAINTENANCE _0304796 REAR DISC BRAKE PAD A

MAINTENANCE  REAR DISC BRAKE PAD  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.


HINT:
·

The following procedure is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:

When replacing a worn rear disc brake pad, the rear disc brake anti-squeal shim kit must be replaced together with the rear disc brake pad.


a.
C366020C01
0.833,1.021 1.365,1.021 false 2.052,0.813 2.583,0.813 false 2.635,0.719 2.948,0.875 0.313,0.156 10 false *a 0.625,0.938 0.938,1.094 0.313,0.156 10 false *b
*a Inner Side (Brown)
*b Outer Side (Green)


Check the rear disc brake pad.

HINT:

If the rear disc brake pad has an identification mark, be sure to confirm the installation location.



b.
C366004C02
0.25,1.063 0.406,0.771 false 0.781,1.198 0.938,0.969 false 1.083,1.719 1.375,1.719 false 1.688,1.906 1.938,1.906 false 2.573,1.219 2.792,1.073 false 2.896,2.01 3.052,1.958 false 2.99,1.719 2.354,1.844 2.354,1.844 2.448,1.427 true 0.583,1.146 0.896,1.302 0.313,0.156 10 false *1 0.073,1.021 0.385,1.177 0.313,0.156 10 false *2 0.885,1.604 1.198,1.76 0.313,0.156 10 false *3 1.49,1.802 1.802,1.958 0.313,0.156 10 false *3 2.813,0.969 3.125,1.125 0.313,0.156 10 false *1 2.729,1.969 2.958,2.135 0.229,0.167 10 false *2 2.188,1.823 2.5,2.021 0.313,0.198 10 false *a
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Pad Wear Indicator Plate
*a Claw


Install 2 new rear disc brake pad wear indicator plates to each rear disc brake pad.

NOTICE:

Install the rear disc brake pad wear indicator plate in the correct positions and direction.



c.

Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to each rear disc brake pad.

NOTICE:
·

Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim in the correct positions and direction as shown in the illustration.

·

Install the No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti squeal shim with the claws in the locations shown in the illustration to the outer side of the vehicle.

·

Install so that the claws are towards the outer side of the vehicle.




Hide 04466 2.INSTALL REAR DISC BRAKE PAD KIT

CAUTION:
·
C368019

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.

Push back the rear disc brake piston.

NOTICE:

Do not forcibly install the rear disc brake piston into rear disc brake cylinder assembly.



b.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Make sure that disc brake grease is applied onto the lining surface of the rear disc brake pad.



c.
C368446C01
2.719,2.177 3.031,2.375 0.313,0.198 10 false *a 2.458,0.885 2.771,1.083 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with a new bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


d.

Depress the brake pedal several times.


Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 5.INSTALL REAR WHEEL