Home › Vehicle Interior › SEAT › SEAT HEATER SYSTEM
RM32K0E _58 Vehicle Interior _061825 SEAT _0303903 SEAT HEATER SYSTEM C

SEAT  SEAT HEATER SYSTEM  B14B5  Lost Communication with Front Seat Temperature Adjustment Switch LIN  


DESCRIPTION

The seat heater switch (air conditioning control assembly) communicates with the air conditioning amplifier assembly via LIN communication.

If the LIN communication system is malfunctioning, the air conditioning amplifier assembly will not operate even if the seat heater switch (air conditioning control assembly) is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area
B14B5 Lost Communication with Front Seat Temperature Adjustment Switch LIN Lost communication with the seat heater switch (air conditioning control assembly)
·

Seat heater switch (air conditioning control assembly)

·

Air conditioning amplifier assembly

·

Wire harness or connector



WIRING DIAGRAM

B474185E03
3.552,0.646 5.198,0.896 1.646,0.25 10 false from IG1 NO. 1 Relay 2.427,0.813 4.073,1.063 1.646,0.25 10 false ECU-IG1 NO. 4 1.375,0.646 1.823,0.854 0.448,0.208 10 false IG+ 1.344,1.198 1.792,1.406 0.448,0.208 10 false LIN1 1.302,1.719 1.75,1.927 0.448,0.208 10 false GND 1.729,0.563 2.177,0.771 0.448,0.208 10 false 10 1.76,1.021 2.208,1.229 0.448,0.208 10 false 2 1.729,1.625 2.177,1.833 0.448,0.208 10 false 16 5.281,1.031 5.729,1.24 0.448,0.208 10 false 14 5.563,1.188 6.01,1.396 0.448,0.208 10 false LIN1 0.344,2.125 0.792,2.333 0.448,0.208 10 false F61 0.333,2.281 2.583,2.667 2.25,0.385 10 false Seat Heater Switch (Air Conditioning Control Assembly) 5.083,2.271 6.656,2.719 1.573,0.448 10 false Air Conditioning Amplifier Assembly 5.083,2.104 5.938,2.354 0.854,0.25 10 false F73 0.833,3.323 2.844,3.563 2.01,0.24 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When DTC B14B2 and B14B5 are output simultaneously, first perform troubleshooting for the air conditioning system.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>B14B2



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B14B5 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (IG POWER SUPPLY - SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - BODY GROUND)
a.
E285189C13
0.167,0.917 0.667,1.167 0.5,0.25 1.333,1.385 0.74,1.76 true 2.25,1.406 2.771,1.792 true 0.115,0.167 0.427,0.323 0.313,0.156 10 false *a 0.292,0.969 0.75,1.167 0.458,0.198 10 false F61 2.688,1.854 3.146,2.052 0.458,0.198 10 false GND 0.625,1.792 1.083,1.99 0.458,0.198 10 false IG+
*a Front view of wire harness connector
(to Seat Heater Switch (Air Conditioning Control Assembly))


Disconnect the seat heater switch (air conditioning control assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F61-10 (IG+) - Body ground Power switch on (IG) 11 to 14 V
Power switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-16 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY))
a.

Disconnect the F61 seat heater switch (air conditioning control assembly) connector.


b.

Disconnect the F73 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-2 (LIN1) - F73-14 (LIN1) Always Below 1 Ω
F61-2 (LIN1) or F73-14 (LIN1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)
a.

Temporarily replace the seat heater switch (air conditioning control assembly) with a new or known good one.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121
OK:

DTC B14B5 is not output.



Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B14B5 is not output.



Result:
Proceed to
OK
NG



OK

END (SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY