Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › QUARTER GARNISH › from 2018.05
RM32K0E _59 Vehicle Exterior _061792 EXTERIOR PANELS / TRIM _0304190 QUARTER GARNISH A

EXTERIOR PANELS / TRIM  QUARTER GARNISH  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75586B 1.INSTALL NO. 2 REAR PILLAR GARNISH PROTECTOR

HINT:

When installing the No. 2 rear pillar garnish protector, heat the quarter pillar cover sub-assembly using a heat light.


Heating Temperature
Item Temperature
Quarter Pillar Cover Sub-assembly 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the quarter pillar cover sub-assembly excessively.


a.

Clean the quarter pillar cover sub-assembly surface.

i.

Using a heat light, heat the quarter pillar cover sub-assembly surface.


ii.

Remove the double-sided tape from the quarter pillar cover sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the quarter pillar cover sub-assembly.


c.

Remove the release paper from a new No. 2 rear pillar garnish protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458887C01
0.583,1.458 0.781,1.219 true 3.042,1.5 3.188,1.115 true 0.823,1.063 1.031,1.26 0.208,0.198 10 true *a 3.156,0.917 3.365,1.115 0.208,0.198 10 true *a
*a Line


Install the No. 2 rear pillar garnish protector as shown in the illustration.

HINT:

Install each No. 2 rear pillar garnish protector along the line on the quarter pillar cover sub-assembly.



Hide 75554E 2.INSTALL QUARTER GARNISH MOULDING (for TMC Made)

HINT:

When installing the quarter garnish moulding, heat the quarter pillar cover sub-assembly using a heat light.


Heating Temperature
Item Temperature
Quarter Pillar Cover Sub-assembly 20 to 30°C (68 to 86°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the quarter pillar cover sub-assembly excessively.


a.

Clean the quarter pillar cover sub-assembly surface.

i.

Using a heat light, heat the quarter pillar cover sub-assembly surface.


ii.

Remove the double-sided tape from the quarter pillar cover sub-assembly.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Using a heat light, heat the quarter pillar cover sub-assembly.


c.

Remove the release paper from a new quarter garnish moulding.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



d.
B458888C01
1.385,1.625 1.052,1.458 true 2.333,0.969 2.104,0.667 true 1.427,1.583 1.667,1.792 0.24,0.208 10 true *a 2.323,1 2.563,1.208 0.24,0.208 10 true *a
*a Line


Install the quarter garnish moulding as shown in the illustration.

HINT:

Install each quarter garnish moulding along the line on the quarter pillar cover sub-assembly.