Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2018.05
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1352  Increasing Pressure Solenoid (FR)  C1353  Increasing Pressure Solenoid (FL)  C1354  Increasing Pressure Solenoid (RR)  C1355  Increasing Pressure Solenoid (RL)  C1356  Decreasing Pressure Solenoid (FR)  C1357  Decreasing Pressure Solenoid (FL)  C1358  Decreasing Pressure Solenoid (RR)  C1359  Decreasing Pressure Solenoid (RL)  


DESCRIPTION

Each solenoid adjusts the pressure which affects each wheel cylinder according to signals from the skid control ECU (brake booster with master cylinder assembly) and controls the vehicle.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1352 Increasing Pressure Solenoid (FR) 11
1100
1101
1102
1103
1170
·

INF Code: 11

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 1100

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1101

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1102

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1103

-

A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.


·

INF Code: 1170

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1353 Increasing Pressure Solenoid (FL) 13
1106
1107
1108
1109
1172
·

INF Code: 13

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 1106

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1107

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1108

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1109

-

A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.


·

INF Code: 1172

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1354 Increasing Pressure Solenoid (RR) 15
1112
1113
1114
1115
1174
·

INF Code: 15

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 1112

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1113

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1114

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1115

-

A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.


·

INF Code: 1174

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1355 Increasing Pressure Solenoid (RL) 17
1118
1119
1120
1121
1176
·

INF Code: 17

-

A malfunction in the solenoid current monitoring circuit is detected for 0.05 seconds or more.


·

INF Code: 1118

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1119

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1120

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1121

-

A solenoid drive circuit malfunction (flyback diode malfunction) is detected for 0.05 seconds or more.


·

INF Code: 1176

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1356 Decreasing Pressure Solenoid (FR) 12
1104
1105
1171
·

INF Code: 12

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1104

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1105

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1171

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1357 Decreasing Pressure Solenoid (FL) 14
1110
1111
1173
·

INF Code: 14

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1110

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1111

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1173

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1358 Decreasing Pressure Solenoid (RR) 16
1116
1117
1175
·

INF Code: 16

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1116

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1117

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1175

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC
C1359 Decreasing Pressure Solenoid (RL) 18
1122
1123
1177
·

INF Code: 18

-

An open is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1122

-

Overcurrent is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1123

-

Current leakage is detected in the solenoid for 0.05 seconds or more.


·

INF Code: 1177

-

The ECU solenoid output differs from the drain monitoring output (drain monitoring is on when the ECU solenoid is not operating) for 0.05 seconds or more.



·

Wire harness or connector

·

Brake actuator assembly

·

Skid control ECU (brake booster with master cylinder assembly)


Electronically controlled brake system DTC

WIRING DIAGRAM

C353483E04
4.01,0.917 4.823,1.26 0.813,0.344 10 false ABS-MAIN 2.198,0.729 3.438,1.115 1.24,0.385 10 false to Auxiliary Battery 5.24,0.76 5.844,1.135 0.604,0.375 10 false BS 4.958,0.646 5.563,1.021 0.604,0.375 10 false 52 4.927,1.594 5.531,1.969 0.604,0.375 10 false 14 4.948,2.396 5.552,2.771 0.604,0.375 10 false 48 4.948,3.063 5.552,3.438 0.604,0.375 10 false 49 4.958,3.719 5.563,4.094 0.604,0.375 10 false 50 4.958,4.375 5.563,4.75 0.604,0.375 10 false 51 4.948,5.021 5.552,5.396 0.604,0.375 10 false 44 4.938,5.677 5.542,6.052 0.604,0.375 10 false 45 4.948,6.344 5.552,6.719 0.604,0.375 10 false 46 4.948,7 5.552,7.375 0.604,0.375 10 false 47 4.938,7.854 5.542,8.229 0.604,0.375 10 false A39 4.927,8.021 6.99,8.615 2.063,0.594 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.188,7.917 1.917,8.427 1.729,0.51 10 false Brake Actuator Assembly 2.229,8.167 3.177,8.542 0.948,0.375 10 false *1: for LHD 2.094,1.708 2.698,2.083 0.604,0.375 10 false A84 1.667,1.708 2.271,2.083 0.604,0.375 10 false A85 1.688,1.938 2.292,2.313 0.604,0.375 10 false *1 2.135,1.938 2.74,2.313 0.604,0.375 10 false *2 1.74,1.479 2.344,1.854 0.604,0.375 10 false 5 1.708,2.302 2.313,2.677 0.604,0.375 10 false 31 2.125,2.302 2.729,2.677 0.604,0.375 10 false 28 1.708,3.604 2.313,3.979 0.604,0.375 10 false 29 2.125,3.604 2.729,3.979 0.604,0.375 10 false 30 1.719,4.927 2.323,5.302 0.604,0.375 10 false 15 2.125,4.927 2.729,5.302 0.604,0.375 10 false 18 1.708,6.25 2.313,6.625 0.604,0.375 10 false 17 2.115,6.25 2.719,6.625 0.604,0.375 10 false 16 6.135,4.771 6.74,5.146 0.604,0.375 10 false IC 5.219,2.635 5.823,3.01 0.604,0.375 10 false SFRH 5.229,1.708 5.833,2.083 0.604,0.375 10 false +BS 5.219,3.313 5.823,3.688 0.604,0.375 10 false SFLH 5.208,3.948 5.813,4.323 0.604,0.375 10 false SRRH 5.219,4.615 5.823,4.99 0.604,0.375 10 false SRLH 5.208,5.271 5.813,5.646 0.604,0.375 10 false SFRR 5.208,5.927 5.813,6.302 0.604,0.375 10 false SFLR 5.208,6.583 5.813,6.958 0.604,0.375 10 false SRRR 5.198,7.24 5.802,7.615 0.604,0.375 10 false SRLR 1.146,7.229 1.75,7.604 0.604,0.375 10 false SRLR 1.125,6.573 1.729,6.948 0.604,0.375 10 false SRRR 1.156,5.917 1.76,6.292 0.604,0.375 10 false SFLR 1.125,5.25 1.729,5.625 0.604,0.375 10 false SFRR 1.135,4.615 1.74,4.99 0.604,0.375 10 false SRLH 1.125,3.958 1.729,4.333 0.604,0.375 10 false SRRH 1.146,3.292 1.75,3.667 0.604,0.375 10 false SFLH 1.156,2.635 1.76,3.01 0.604,0.375 10 false SFRH 1.229,1.833 1.833,2.208 0.604,0.375 10 false +BS 2.167,1.49 2.771,1.865 0.604,0.375 10 false 5 1.656,2.51 2.26,2.885 0.604,0.375 10 false A85 1.646,3.156 2.25,3.531 0.604,0.375 10 false A85 1.656,3.813 2.26,4.188 0.604,0.375 10 false A85 1.656,4.479 2.26,4.854 0.604,0.375 10 false A85 1.656,5.135 2.26,5.51 0.604,0.375 10 false A85 1.656,5.792 2.26,6.167 0.604,0.375 10 false A85 1.656,6.448 2.26,6.823 0.604,0.375 10 false A85 1.656,7.115 2.26,7.49 0.604,0.375 10 false A85 2.083,2.51 2.688,2.885 0.604,0.375 10 false A84 2.073,3.156 2.677,3.531 0.604,0.375 10 false A84 2.083,3.813 2.688,4.188 0.604,0.375 10 false A84 2.073,4.469 2.677,4.844 0.604,0.375 10 false A84 2.073,5.135 2.677,5.51 0.604,0.375 10 false A84 2.094,5.792 2.698,6.167 0.604,0.375 10 false A84 2.083,6.448 2.688,6.823 0.604,0.375 10 false A84 2.083,7.115 2.688,7.49 0.604,0.375 10 false A84 1.688,2.74 2.292,3.115 0.604,0.375 10 false *1 1.688,3.396 2.292,3.771 0.604,0.375 10 false *1 1.698,4.042 2.302,4.417 0.604,0.375 10 false *1 1.698,4.708 2.302,5.083 0.604,0.375 10 false *1 1.688,5.365 2.292,5.74 0.604,0.375 10 false *1 1.698,6.031 2.302,6.406 0.604,0.375 10 false *1 1.688,6.688 2.292,7.063 0.604,0.375 10 false *1 1.719,7.344 2.323,7.719 0.604,0.375 10 false *1 2.104,2.74 2.708,3.115 0.604,0.375 10 false *2 2.115,3.396 2.719,3.771 0.604,0.375 10 false *2 2.125,4.042 2.729,4.417 0.604,0.375 10 false *2 2.115,4.708 2.719,5.083 0.604,0.375 10 false *2 2.115,5.365 2.719,5.74 0.604,0.375 10 false *2 2.125,6.031 2.729,6.406 0.604,0.375 10 false *2 2.115,6.688 2.719,7.063 0.604,0.375 10 false *2 2.125,7.344 2.729,7.719 0.604,0.375 10 false *2 1.698,2.948 2.302,3.323 0.604,0.375 10 false 28 2.125,2.948 2.729,3.323 0.604,0.375 10 false 31 1.719,4.271 2.323,4.646 0.604,0.375 10 false 30 2.125,4.271 2.729,4.646 0.604,0.375 10 false 29 1.708,5.594 2.313,5.969 0.604,0.375 10 false 18 2.125,5.594 2.729,5.969 0.604,0.375 10 false 15 1.708,6.896 2.313,7.271 0.604,0.375 10 false 16 2.125,6.896 2.729,7.271 0.604,0.375 10 false 17 3.385,8.167 4.333,8.542 0.948,0.375 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly) or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



C385605C02
0.979,1.563 0.688,0.802 true 2.125,1.323 2.302,0.719 true 3.042,1.563 3.313,0.813 true 3.458,2.063 2.906,1.635 true 2.948,2.458 2.771,1.635 true 2.354,2.198 2.635,1.635 true 0.594,2.042 1.104,1.646 true 1.083,2.458 1.229,1.646 true 1.677,2.198 1.354,1.646 true 6.458,1.563 6.729,0.813 true 5.583,1.323 5.802,0.74 true 4.417,1.563 4.156,0.813 true 4.167,2.052 4.542,1.635 true 4.552,2.385 4.677,1.635 true 5.167,2.24 4.802,1.646 true 5.729,2.229 6.073,1.635 true 6.333,2.396 6.208,1.646 true 6.75,2.042 6.323,1.635 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.5,0.635 0.938,0.823 0.438,0.188 10 false SFRH 2.188,0.552 2.5,0.75 0.313,0.198 10 false +BS 0.344,1.365 0.656,1.563 0.313,0.198 10 false *A 3.823,1.354 4.135,1.552 0.313,0.198 10 false *B 3.156,0.646 3.594,0.833 0.438,0.188 10 false SFRR 3.292,2.073 3.729,2.26 0.438,0.188 10 false SRLR 2.823,2.49 3.26,2.677 0.438,0.188 10 false SRRR 2.167,2.208 2.604,2.396 0.438,0.188 10 false SFLR 1.521,2.208 1.958,2.396 0.438,0.188 10 false SFLH 0.885,2.479 1.323,2.667 0.438,0.188 10 false SRRH 0.354,2.052 0.792,2.24 0.438,0.188 10 false SRLH 3.979,0.646 4.417,0.833 0.438,0.188 10 false SFLH 5.698,0.573 6.01,0.771 0.313,0.198 10 false +BS 6.583,0.646 7.021,0.833 0.438,0.188 10 false SFLR 6.656,2.052 7.094,2.24 0.438,0.188 10 false SRRR 6.198,2.406 6.635,2.594 0.438,0.188 10 false SRLR 5.583,2.25 6.021,2.438 0.438,0.188 10 false SFRR 5.01,2.25 5.448,2.438 0.438,0.188 10 false SFRH 4.333,2.406 4.771,2.594 0.438,0.188 10 false SRLH 3.948,2.073 4.385,2.26 0.438,0.188 10 false SRRH
*A for LHD *B for RHD
*a Component without harness connected
(Brake Actuator Assembly)
- -


b.

Disconnect the A85 brake actuator assembly connector (for LHD).


c.

Disconnect the A84 brake actuator assembly connector (for RHD).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

HINT:

Check the brake actuator assembly when it is cooled down.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
5 (+BS) - 31 (SFRH) Always 6.4 to 7.0 Ω
5 (+BS) - 28 (SFLH) Always 6.4 to 7.0 Ω
5 (+BS) - 29 (SRRH) Always 6.4 to 7.0 Ω
5 (+BS) - 30 (SRLH) Always 6.4 to 7.0 Ω
5 (+BS) - 15 (SFRR) Always 5.1 to 5.7 Ω
5 (+BS) - 18 (SFLR) Always 5.1 to 5.7 Ω
5 (+BS) - 17 (SRRR) Always 5.1 to 5.7 Ω
5 (+BS) - 16 (SRLR) Always 5.1 to 5.7 Ω

for RHD
Tester Connection Condition Specified Condition
5 (+BS) - 28 (SFRH) Always 6.4 to 7.0 Ω
5 (+BS) - 31 (SFLH) Always 6.4 to 7.0 Ω
5 (+BS) - 30 (SRRH) Always 6.4 to 7.0 Ω
5 (+BS) - 29 (SRLH) Always 6.4 to 7.0 Ω
5 (+BS) - 18 (SFRR) Always 5.1 to 5.7 Ω
5 (+BS) - 15 (SFLR) Always 5.1 to 5.7 Ω
5 (+BS) - 16 (SRRR) Always 5.1 to 5.7 Ω
5 (+BS) - 17 (SRLR) Always 5.1 to 5.7 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

B

C

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
A39-14 (+BS) - A85-5 (+BS) Always Below 1 Ω
A39-14 (+BS) or A85-5 (+BS) - Body ground Always 10 kΩ or higher
A39-48 (SFRH) - A85-31 (SFRH) Always Below 1 Ω
A39-48 (SFRH) or A85-31 (SFRH) - Body ground Always 10 kΩ or higher
A39-49 (SFLH) - A85-28 (SFLH) Always Below 1 Ω
A39-49 (SFLH) or A85-28 (SFLH) - Body ground Always 10 kΩ or higher
A39-50 (SRRH) - A85-29 (SRRH) Always Below 1 Ω
A39-50 (SRRH) or A85-29 (SRRH) - Body ground Always 10 kΩ or higher
A39-51 (SRLH) - A85-30 (SRLH) Always Below 1 Ω
A39-51 (SRLH) or A85-30 (SRLH) - Body ground Always 10 kΩ or higher
A39-44 (SFRR) - A85-15 (SFRR) Always Below 1 Ω
A39-44 (SFRR) or A85-15 (SFRR) - Body ground Always 10 kΩ or higher
A39-45 (SFLR) - A85-18 (SFLR) Always Below 1 Ω
A39-45 (SFLR) or A85-18 (SFLR) - Body ground Always 10 kΩ or higher
A39-46 (SRRR) - A85-17 (SRRR) Always Below 1 Ω
A39-46 (SRRR) or A85-17 (SRRR) - Body ground Always 10 kΩ or higher
A39-47 (SRLR) - A85-16 (SRLR) Always Below 1 Ω
A39-47 (SRLR) or A85-16 (SRLR) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
A39-14 (+BS) - A84-5 (+BS) Always Below 1 Ω
A39-14 (+BS) or A84-5 (+BS) - Body ground Always 10 kΩ or higher
A39-48 (SFRH) - A84-28 (SFRH) Always Below 1 Ω
A39-48 (SFRH) or A84-28 (SFRH) - Body ground Always 10 kΩ or higher
A39-49 (SFLH) - A84-31 (SFLH) Always Below 1 Ω
A39-49 (SFLH) or A84-31 (SFLH) - Body ground Always 10 kΩ or higher
A39-50 (SRRH) - A84-30 (SRRH) Always Below 1 Ω
A39-50 (SRRH) or A84-30 (SRRH) - Body ground Always 10 kΩ or higher
A39-51 (SRLH) - A84-29 (SRLH) Always Below 1 Ω
A39-51 (SRLH) or A84-29 (SRLH) - Body ground Always 10 kΩ or higher
A39-44 (SFRR) - A84-18 (SFRR) Always Below 1 Ω
A39-44 (SFRR) or A84-18 (SFRR) - Body ground Always 10 kΩ or higher
A39-45 (SFLR) - A84-15 (SFLR) Always Below 1 Ω
A39-45 (SFLR) or A84-15 (SFLR) - Body ground Always 10 kΩ or higher
A39-46 (SRRR) - A84-16 (SRRR) Always Below 1 Ω
A39-46 (SRRR) or A84-16 (SRRR) - Body ground Always 10 kΩ or higher
A39-47 (SRLR) - A84-17 (SRLR) Always Below 1 Ω
A39-47 (SRLR) or A84-17 (SRLR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.RECONFIRM DTC
a.

Reconnect the A39 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A85 brake actuator assembly connector (for LHD).


c.

Reconnect the A84 brake actuator assembly connector (for RHD).


d.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

e.

Turn the power switch off.


f.

Turn the power switch on (IG).


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 and C1359 are not output. A
DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 or C1359 are output. (for LHD) B
DTCs C1352, C1353, C1354, C1355, C1356, C1357, C1358 or C1359 are output. (for RHD) C



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY