Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2018.05–2019.09
RM32K0E _54 Brake _060044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294924 ELECTRONICALLY CONTROLLED BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA/INFORMATION


a.

Using the GTS, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.


b.

The Freeze Frame Data that is recorded when a DTC is stored can be used to check the INF codes, but only for DTCs which can be stored.



CHECK FREEZE FRAME DATA WHEN BRAKE SYSTEM OPERATES


a.

Freeze Frame Data is stored when the brake system operates. The Freeze Frame Data is updated each time the system operates.


b.

Once Freeze Frame Data is stored when the system operates, it is not cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the power switch has been turned from off to on (IG) since the last time the system was activated can be stored and displayed.

HINT:
·

When the vehicle is stopped (vehicle speed below 7 km/h (4 mph)), turning the power switch from off to on (IG) does not cause the value to increase.

·

The value "31" is displayed when the power switch was turned on (IG) more than 31 times.




d.

Check Freeze Frame Data when the system operates.

i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3 and turn the power switch on (IG).


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility.


iv.

Select "ABS History".

Chassis > ABS/VSC/TRC > Utility
Tester Display
ABS History
50005 105 8

v.

Check the Freeze Frame Data when the system operates.




CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED


a.

Freeze Frame Data is stored when a DTC is output.


b.

Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.


c.

The number of times (maximum: 31) the power switch has been turned from off to on (IG) since a DTC was output can be stored and displayed.

HINT:

The value "31" is displayed when the power switch was turned on (IG) more than 31 times.



d.

Check the Freeze Frame Data and INF code when a DTC is output.

i.

Turn the power switch off.


ii.

Connect the GTS to the DLC3 and turn the power switch on (IG).


iii.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

iv.

Select a DTC to display the Freeze Frame Data.


v.

Check the Freeze Frame Data for the output DTC.

HINT:

If an "INF Code" item appears when the Freeze Frame Data is displayed, select and check the INF code.


Chassis > ABS/VSC/TRC
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RR Speed Open Rear speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Open Rear speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Open Yaw rate sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Deceleration Open Acceleration sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Steering Open Steering angle sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Stroke Open Brake pedal stroke sensor assembly open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Stroke2 Open Brake pedal stroke sensor assembly 2 open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Accumulator Open Accumulator pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
HV Communication Open Hybrid vehicle communication open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FR Speed Sensor Voltage Open Front speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Sensor Voltage Open Front speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
RL Speed Sensor Voltage Open Rear speed sensor LH voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Yaw Rate Sensor Voltage Open Yaw rate sensor voltage open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Detailed Freeze DTC Detailed code for Freeze Frame DTC Min.: 0, Max.: 65535 - Number of information codes (INF codes) output is displayed
Number of IG ON Number of times power switch turned on (IG) after Freeze Frame Data stored 0 to 31 - -
Buzzer Meter buzzer ON or OFF ON: Buzzer on
OFF: Buzzer off
-
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW Parking brake switch assembly ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
TRC(TRAC)/VSC OFF SW VSC OFF switch (Electric parking brake switch assembly) ON or OFF ON: Switch on
OFF: Switch off
-
Reservoir Warning SW Brake fluid level warning switch ON or OFF ON: Reservoir level low
OFF: Reservoir level normal
-
Shift Lever Position Shift position information Fail, 1st, 2nd, 3rd, 4th, 5th, 6th/B, D/M, P,N or R Actual shift position -
Operated System Operated system status Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC, MCB, Sys Actual operated system Non: No operation is activated.
ABS: ABS is activated.
VSC: VSC is activated.
TRC: TRC is activated.
BA: BA is activated.
HAB: HAB is activated.*
Fail: Fail safe mode is activated.
PBA: PBA is activated.
PB: PB is activated.*
HA-CTRL: Hill-start assist control is activated.
MCB:SCB
Sys: System prohibit is activated.
Stroke Sensor Brake pedal stroke sensor assembly Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.65 to 1.35 V Reading increases when brake pedal is depressed
Stroke Sensor Grade Brake pedal stroke sensor assembly change Min.: -2560 mm/s, Max.: 2540 mm/s Brake pedal released or depressed and held: 0 mm/s Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal
Stroke Sensor2 Brake pedal stroke sensor assembly 2 Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 3.65 to 4.35 V Reading decreases when brake pedal is depressed
Yaw Rate Sensor Yaw rate sensor Min.: -128 °/s, Max.: 127 °/s Vehicle stopped: 0 degrees/s
Turning right: -128 to 0 degrees/s
Turning left: 0 to 127 degrees/s
-
Lateral G Lateral G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and backward G Min.: -25.10 m/s2, Max.: 24.90 m/s2 - During acceleration/deceleration: Changes in proportion with acceleration
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Grade Vehicle acceleration Min.: -25.10 m/s2, Max.: 24.90 m/s2 Vehicle stopped: 0 m/s2 During driving: Changes in proportion with vehicle acceleration/deceleration
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 127.5% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
ECB Motor Relay Motor relay 1 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Motor Relay2 Motor relay 2 operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
ECB Main Relay Main relay operation request ON or OFF ON: Relay on
OFF: Relay off
ECB: Electronically Controlled Brake System
IG1 Voltage Value IG1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
IG2 Voltage Value IG2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
BS1 Voltage Value BS1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
BS2 Voltage Value BS2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
VM1 Voltage Value VM1 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
VM2 Voltage Value VM2 voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to auxiliary battery voltage
Motor Relay Voltage Value Motor relay voltage value Min.: 0.00 V, Max.: 20.00 V - -
FR Target Oil Pressure Front wheel RH target oil pressure Min.: 0.00 MPa, Max.: 20.00 MPa - Different according to target oil pressure of each wheel
FL Target Oil Pressure Front wheel LH target oil pressure Min.: 0.00 MPa, Max.: 20.00 MPa - Different according to target oil pressure of each wheel
RR Target Oil Pressure Rear wheel RH target oil pressure Min.: 0.00 MPa, Max.: 20.00 MPa - Different according to target oil pressure of each wheel
RL Target Oil Pressure Rear wheel LH target oil pressure Min.: 0.00 MPa, Max.: 20.00 MPa - Different according to target oil pressure of each wheel
Inspection Mode Inspection mode Other or Inspect Other: Normal mode
Inspect: Inspection mode
-
Steering Angle Sensor Steering angle sensor Min.: - 3276.8°, Max.: 3276.7° Turning left: Increases
Turning right: Decreases
-
VCM1 Voltage Value VCM1 voltage value Min.: 0.00 V, Max.: 10.00 V 6.29 to 7.64 V -
VCM2 Voltage Value VCM2 voltage value Min.: 0.00 V, Max.: 10.00 V 6.29 to 7.64 V -
TRC/VSC Off Mode TRC/VSC off mode Normal, TRC OFF, VSC Expert Mode or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC Expert Mode: VSC expert mode
VSC OFF: VSC off mode
-
Brake Hold Control Brake hold control status OFF, Hold, Release, EPB OFF: Brake hold control not operating
Hold: Brake hold operating during brake hold control
Release: Brake hold released during brake hold control
EPB: Electric parking brake operating during brake hold control
EPB: Electric Parking Brake System
Regulator Pressure Sensor Output Variant Reaction force pressure sensor output variant Min.: -30 MPa/s, Max.: 225 MPa/s - -
SLA Solenoid Current Linear solenoid additional valve (SLA) current Min.: 0.00 A, Max.: 1.50 A Brake pedal released: 0.00 A -
SLR Solenoid Current Linear solenoid reduction valve (SLR) current Min.: 0.00 A, Max.: 1.50 A Brake pedal released: 0.00 A -
Target Oil Pressure Wheel target hydraulic pressure Min.: 0.00 MPa, Max.: 20.00 MPa - Changes according to the target wheel cylinder hydraulic pressure
Voltage of Stroke Sensor Voltage of brake pedal stroke sensor assembly Min.: -2.50 V, Max.: 2.49 V - -
Voltage of Stroke Sensor2 Voltage of brake pedal stroke sensor assembly 2 Min.: -2.50 V, Max.: 2.49 V - -
IG Switch Power switch on (IG) status ON or OFF - -
Elapsed Time after Freeze Trigger Elapsed time after storing Freeze Frame Data Min.: 0 msec, Max.: 1020 msec - -
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa, Max.: 24.48 MPa 0.00 to 21.60 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Brake pedal released: 0.00 MPa
Servo Pressure Pressure value of servo Min.: 0.00 MPa, Max.: 24.48 MPa 0.00 to 21.60 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Brake pedal released: 0.00 to 2.10 MPa
Reaction Force Pressure Sensor Temperature Reaction force pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
Servo Pressure Sensor Temperature Servo pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
Accumulator Pressure Sensor Temperature Accumulator pressure sensor temperature Min.: -80°C (-112°F), Max.: 175°C (347°F) -30°C (-22°F) to 100°C (212°F) -
Accumulator Pressure Accumulator pressure output value Min.: 0.00 MPa, Max.: 24.48 MPa 0.00 to 21.60 MPa When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator
MT Voltage Value (ABS) ABS motor voltage value Min.: 0.00 V, Max.: 20.00 V ABS motor off: 0.00 V
ABS motor on: 11.00 to 14.00 V
-
VCSK Voltage Value VCSK voltage value Min.: 0.000 V, Max.: 5.500 V 4.800 to 5.200 V -
ECB Solenoid (SGH) Switching solenoid valve (SGH) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
ECB Solenoid (SSA) Switching solenoid valve (SSA) ON or OFF ON: Solenoid on
OFF: Solenoid off
ECB: Electronically Controlled Brake System
Reaction Force Pressure Sensor Open Reaction force pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Servo Pressure Sensor Open Servo pressure sensor open detection Error or Normal Error: Momentary interruption
Normal: Normal
-



CLEAR FREEZE FRAME DATA AND INFORMATION


NOTICE:

Clearing the DTCs will also clear the Freeze Frame Data and information codes (INF codes).


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs and Freeze Frame Data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105