MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU and airbag ECU detect that a collision has occurred and shut off the system main relay.
The cause of this DTC may be one of the following:
Collision is detected
Detection sensor system malfunction
Airbag system malfunction
Hybrid vehicle control ECU malfunction
Communication malfunction between airbag ECU and hybrid vehicle control ECU
Hybrid vehicle control ECU communication malfunction
The hybrid vehicle control ECU receives a signal that indicates a collision from the airbag ECU assembly to detect a collision. After detecting a collision, the hybrid vehicle control ECU shuts off the high voltage systems for safety.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P160600 | Collision detected or Collision Sensor Connection (Open) | Collision detection
A block signal is received from the airbag ECU assembly. (1 trip detection logic) |
·
Airbag ECU assembly ·
Hybrid vehicle control ECU ·
Airbag system |
Does not come on | Master Warning:
Comes on |
| P160604 | Collision detected or Collision Sensor Connection (Open) System Internal Failure | Collision detection
Multiple wiring malfunctions occur simultaneously. (1 trip detection logic) |
·
Hybrid vehicle control ECU ·
Airbag system |
Does not come on | Master Warning:
Comes on |
If P160600 or P160604 is output, the hybrid system cannot be started unless the DTCs are cleared using the GTS.
| DTC No. | Data List |
|---|---|
| P160600 | ·
Airbag Status (Collision) ·
Airbag Status (Normal) |
| P160604 |
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for 2 minutes or more.
Turn the power switch on (IG) and turn the GTS on.
With power switch on (IG) and wait for 5 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| The vehicle is not damaged. | A |
| The vehicle is damaged. | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P160600 or P160604 only is output, or DTCs except the ones in the table below are also output. | A |
| Any of the following DTCs including pending DTCs are also output. | B |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | |
| P060A29 | Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid | |
| P060A44 | Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure | |
| P060A45 | Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure | |
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | |
| P060A49 | Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure | |
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | |
| P060B1C | Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range | |
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | |
| P060B71 | Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck | |
| P06881F | ECM/PCM Power Relay Sense Circuit Intermittent | |
| P1C9E9F | Hybrid/EV System Reset Stuck Off | |
| P1CE31C | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range | |
| P1CE349 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure | |
| P1CE371 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck | |
P160600 or P160604 may be output as a result of the malfunction indicated by the DTCs above.
Turn the power switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| P160600 is output. | A |
| P160604 is output. | B |
Turn the power switch off.
A
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs of hybrid control system in the table below are output. | A |
| DTCs of motor generator control system in the table below are output. | B |
| System | Relevant DTC | |
|---|---|---|
| Hybrid control system | P310711 | Lost Communication with Airbag System Control Module Circuit Short to Ground (Low) |
| P310715 | Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open (High) | |
| U015187 | Lost Communication with Restraints Control Module Missing Message | |
| Motor generator control system | P312487 | Lost Communication between Drive Motor "A" and HV ECU Missing Message |
Turn the power switch off.
A
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B