Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › from 2018.05
RM32K0E _54 Brake _060048 PARKING BRAKE _0296497 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C13AD  Open in +B Circuit  


DESCRIPTION

The parking brake ECU (brake actuator assembly) operates the parking brake motor RH and LH with power supplied from the BEPB terminals.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C13AD Open in +B Circuit All of following conditions are met:
1.

Power switch on (IG) or electric parking brake switch (electric parking brake switch assembly) pulled to lock side with power switch off.

2.

When parking brake motor is not operating, Motor +B voltage is Mid or when parking brake motor is operating, Motor +B voltage is Lo

3.

When parking brake motor is not operating, malfunction is detected for approximately 1 second When parking brake motor is operating, malfunction is detected for approximately 0.5 seconds


·

Wire harness or connector

·

parking brake ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition Power switch on (IG) ○ - ○ -
Electric parking brake switch (electric parking brake switch assembly) pushed to release side with power switch off - ○ - ○
Malfunction Status When parking brake is not operating: Motor +B voltage is Mid ○ ○ - -
When parking brake is operating: Motor +B voltage is Lo - - ○ ○
Detection Time Approximately 1 second Approximately 1 second Approximately 0.5 seconds Approximately 0.5 seconds
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C393538E01
3.438,1.094 3.594,1.292 0.156,0.198 10 false 9 3.802,1.094 3.958,1.292 0.156,0.198 10 false 9 1.281,1.469 2.125,1.667 0.844,0.198 10 false EPB NO. 1 3.365,1.302 3.667,1.49 0.302,0.188 10 false A84 3.719,1.302 4.021,1.49 0.302,0.188 10 false A85 3.396,1.521 3.635,1.708 0.24,0.188 10 false *2 3.76,1.521 4,1.708 0.24,0.188 10 false *1 4.104,1.302 4.573,1.521 0.469,0.219 10 false BEPB 3.979,2.427 5.625,2.833 1.646,0.406 10 false Parking Brake ECU (Brake Actuator Assembly) 0.396,3.031 1.219,3.26 0.823,0.229 10 false *1: for LHD 0.396,3.365 1.219,3.594 0.823,0.229 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The electric parking brake may still operate up to 20 seconds after the power switch is turned off. Before disconnecting connectors or fuses, turn the power switch off and wait 20 seconds or more.

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the power switch is first turned on (IG).



PROCEDURE

1.READ VALUE USING GTS (RH MOTOR +B VOLTAGE AND LH MOTOR +B VOLTAGE)
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Electric Parking Brake / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RH Motor +B Voltage Parking brake motor RH (parking brake actuator assembly RH) +B voltage Lo, Mid or Hi Hi: Power switch on (IG) Mid: +B voltage is less than 8.5 V*
Lo: +B voltage is less than 3.5 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


LH Motor +B Voltage Parking brake motor LH (parking brake actuator assembly LH) +B voltage Lo, Mid or Hi Hi: Power switch on (IG) Mid: +B voltage is less than 8.5 V*
Lo: +B voltage is less than 3.5 V*
HINT:

*: When the auxiliary battery voltage is 12 V.


Chassis > Electric Parking Brake > Data List
Tester Display
RH Motor +B Voltage
LH Motor +B Voltage
50003 184 427,428

Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - BATTERY)
2.CHECK HARNESS AND CONNECTOR (PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY) - BATTERY)
a.

Turn the power switch off.


b.
C393510C01
1.583,2.333 2,2.583 0.417,0.25 1.583,0.25 2,0.5 0.417,0.25 2.531,1.146 2.708,0.521 true 2.542,3.281 2.719,2.656 true 1.677,2.375 2.135,2.573 0.458,0.198 10 false A85 1.677,0.292 2.135,0.49 0.458,0.198 10 false A84 2.073,0.292 2.531,0.49 0.458,0.198 10 false *B 2.083,2.375 2.542,2.573 0.458,0.198 10 false *A 0.125,0.083 0.583,0.281 0.458,0.198 10 false *a 2.542,0.323 3,0.521 0.458,0.198 10 false BEPB 2.552,2.469 3.01,2.667 0.458,0.198 10 false BEPB
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Parking Brake ECU (Brake Actuator Assembly))


Disconnect the parking brake ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
A85-9 (BECU) - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
A84-9 (BECU) - Body ground Always 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR