83100
1.INSPECT COMBINATION METER ASSEMBLY
Check speedometer operation
The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (skid control ECU) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (skid control ECU) because it is the source of the vehicle speed signal.
Data List values of the brake actuator assembly (skid control ECU) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Warm up the engine.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| Vehicle Speed |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 21.0 to 25.0 |
| 40 | 41.7 to 46.2 |
| 60 | 62.7 to 67.2 |
| 80 | 83.4 to 88.4 |
| 100 | 104.3 to 109.3 |
| 120 | 125.1 to 130.6 |
| 140 | 145.8 to 151.8 |
| 160 | 166.2 to 173.2 |
| 180 | 186.9 to 194.5 |
| 200 | 207.7 to 215.7 |
| 220 | 228.4 to 236.8 |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 20.6 to 24.2 |
| 40 | 41.2 to 44.8 |
| 60 | 61.8 to 65.4 |
| 80 | 82.4 to 86.0 |
| 100 | 103.0 to 106.6 |
| 120 | 123.6 to 127.4 |
| 140 | 144.2 to 148.2 |
| 160 | 164.9 to 168.9 |
| 180 | 185.7 to 189.3 |
| 200 | 206.3 to 209.9 |
| 220 | 226.7 to 230.7 |
| GTS Indication (mph) | Acceptable Range (mph) |
|---|---|
| 20 | 19.3 to 21.8 |
| 40 | 39.5 to 42.3 |
| 60 | 60.0 to 62.8 |
| 80 | 80.2 to 83.4 |
| 100 | 100.7 to 103.9 |
| 120 | 121.2 to 124.4 |
| 140 | 141.6 to 144.8 |
Speedometer reading is within the acceptable range at each vehicle speed.
Check LED illumination (LED check)
Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).
| Warning or Indicator Light | Control ECU | Specified Condition |
|---|---|---|
| Brake warning light | Brake actuator assembly (Skid control ECU) | Warning or indicator light comes on for about 3 seconds after turning the power switch to on (IG). |
| VSC OFF indicator light | Brake actuator assembly (Skid control ECU) | |
| Slip indicator light | Brake actuator assembly (Skid control ECU) | |
| ABS warning light | Brake actuator assembly (Skid control ECU) | |
| Tire pressure warning light | Tire pressure warning and ECU receiver | |
| PCS OFF warning light*1 | Millimeter wave radar sensor assembly | |
| Automatic high beam indicator light*1 | Main body ECU (Multiplex network body ECU) | |
| EPB indicator light | Brake actuator assembly (Skid control ECU) | |
| EPB warning light | Brake actuator assembly (Skid control ECU) | |
| High beam indicator light | Main body ECU (Multiplex network body ECU) | |
| BSM OFF indicator light*2 | Blind spot monitor sensor LH (B) | |
| RCTA OFF indicator light*2 | Blind spot monitor sensor LH (B) | |
| SRS warning light | Airbag sensor assembly | Warning light comes on for about 6 seconds after turning the power switch to on (IG). |
| Charge warning light | ECM | Warning light comes on when the power switch to on (IG). |
| MIL (Check engine warning light) | ECM | |
| EPS warning light | Power steering ECU assembly | |
| IPA indicator light*2 | Clearance warning ECU assembly |
*1: w/ Toyota Safety Sense
*2: w/ Blind Spot Monitor System