Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.09
RM32K0E _58 Vehicle Interior _062180 METER / GAUGE / DISPLAY _0304590 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

These DTCs are stored when the combination meter assembly detects an open in a turn signal light circuit, or a short in a turn signal light circuit or the hazard warning light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1507 Open in Turn Signal Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Open in turn signal light circuit


·

Bulb*1

·

LED*2

·

Harness or connector

·

Combination meter assembly


DTC stored -
B1508 Short in Turn Signal / Hazard Flasher Circuit When IG voltage is 9.5 V or more and the following condition is detected:
·

Short in turn signal light circuit or hazard warning light circuit


·

Bulb*1

·

LED*2

·

Harness or connector

·

Combination meter assembly


DTC stored -

*1: for Bulb Type Turn Signal Light

*2: for LED Type Turn Signal Light


WIRING DIAGRAM

FOR RH SIDE TURN SIGNAL LIGHT


E426559E03
2.49,0.521 2.646,0.719 0.156,0.198 10 false B 2.51,1.635 2.667,1.833 0.156,0.198 10 false B 1.135,1.646 1.292,1.844 0.156,0.198 10 false E 1.135,0.531 1.292,0.729 0.156,0.198 10 false E 2.771,3.083 2.927,3.281 0.156,0.198 10 false B 0.427,3.906 2.813,4.229 2.385,0.323 10 false Side Turn Signal Light Assembly RH*3 5.25,2.781 5.823,3.427 0.573,0.646 10 false Flasher Relay IC 6.229,3.552 6.688,3.75 0.458,0.198 10 false CPU 5.906,0.906 6.615,1.219 0.708,0.313 10 false Turn RH 4.906,6.594 5.219,6.792 0.313,0.198 10 false F5 4.896,6.771 6.875,7.25 1.979,0.479 10 false Combination Meter Assembly 4.615,0.521 4.927,0.719 0.313,0.198 10 false LR 0.448,4.302 0.76,4.5 0.313,0.198 10 false I8 0.438,4.448 2.969,4.844 2.531,0.396 10 false Outer Rear View Mirror Assembly RH*3 3.167,0.521 3.479,0.719 0.313,0.198 10 false *1 3.177,1.646 3.49,1.844 0.313,0.198 10 false *2 2.979,5.083 3.271,5.354 0.292,0.271 10 false 16 3,3.542 3.156,3.74 0.156,0.198 10 false 2 2.708,1.635 2.865,1.833 0.156,0.198 10 false 2 2.698,0.531 2.854,0.729 0.156,0.198 10 false 2 0.948,0.531 1.104,0.729 0.156,0.198 10 false 6 0.948,1.646 1.104,1.844 0.156,0.198 10 false 6 4.427,0.521 4.583,0.719 0.156,0.198 10 false 7 1.135,1 1.594,1.198 0.458,0.198 10 false A89 1.104,2.135 1.563,2.333 0.458,0.198 10 false A89 1.125,1.167 2.813,1.531 1.688,0.365 10 false Headlight Assembly RH*1 1.094,2.313 2.781,2.677 1.688,0.365 10 false Headlight Assembly RH*2 0.167,7.083 2.167,7.417 2,0.333 10 false *1: for Triple Beam Headlight 0.177,7.427 2.563,7.76 2.385,0.333 10 false *2: for Single Beam Headlight 2.979,3.083 3.135,3.281 0.156,0.198 10 false 1 3,5.531 3.281,5.771 0.281,0.24 10 false 12 2.771,3.542 2.927,3.74 0.156,0.198 10 false E 2.76,5.521 2.917,5.719 0.156,0.198 10 false - 2.76,5.083 2.917,5.281 0.156,0.198 10 false B 3.406,3.083 3.719,3.281 0.313,0.198 10 false *3 3.844,3.521 4.156,3.719 0.313,0.198 10 false *4 0.49,5.99 2.875,6.313 2.385,0.323 10 false Side Turn Signal Light Assembly RH*4 0.469,6.49 0.781,6.688 0.313,0.198 10 false I7 0.469,6.656 3,7.052 2.531,0.396 10 false Outer Rear View Mirror Assembly RH*4 2.333,7.083 4.333,7.417 2,0.333 10 false *3: for TMMT Made 2.333,7.417 4.719,7.75 2.385,0.333 10 false *4: for TMC Made

E426529E03
2.302,1.021 2.813,1.25 0.51,0.229 10 false TRN 1.135,1.021 1.292,1.219 0.156,0.198 10 false E 2.5,4.552 2.656,4.75 0.156,0.198 10 false B 1.135,4.552 1.292,4.75 0.156,0.198 10 false E 5.25,3.26 5.823,3.906 0.573,0.646 10 false Flasher Relay IC 6.229,4.167 6.688,4.365 0.458,0.198 10 false CPU 4.906,6.594 5.219,6.792 0.313,0.198 10 false F5 4.896,6.771 6.875,7.25 1.979,0.479 10 false Combination Meter Assembly 4.615,1.021 5.313,1.24 0.698,0.219 10 false TRNR 3.167,1.021 3.479,1.219 0.313,0.198 10 false *1 3.854,1.74 4.167,1.938 0.313,0.198 10 false *2 2.698,4.448 2.854,4.646 0.156,0.198 10 false 1 0.958,4.448 1.115,4.646 0.156,0.198 10 false 2 2.708,2.365 2.865,2.563 0.156,0.198 10 false 5 2.698,1.021 2.854,1.219 0.156,0.198 10 false 4 0.948,1.021 1.104,1.219 0.156,0.198 10 false 3 0.938,2.365 1.094,2.563 0.156,0.198 10 false 4 4.427,1.01 4.583,1.208 0.156,0.198 10 false 5 1.094,1.5 2.083,1.75 0.99,0.25 10 false M47*3, o1*4 1.135,4.885 1.708,5.083 0.573,0.198 10 false S15 1.135,5.042 2.885,5.427 1.75,0.385 10 false Rear Light Assembly RH*2 1.094,3.323 2.583,4 1.49,0.677 10 false Rear Combination Light Assembly RH*2 1.094,1.646 2.552,2.302 1.458,0.656 10 false Rear Combination Light Assembly RH*1 1.094,3.188 2.208,3.365 1.115,0.177 10 false M114*3, o2*4 2.344,2.469 2.802,2.667 0.458,0.198 10 false TRN 0.958,4.031 1.115,4.229 0.156,0.198 10 false 5 2.698,4.042 2.854,4.24 0.156,0.198 10 false 6 1.135,2.458 1.292,2.656 0.156,0.198 10 false E 0.938,2.781 1.094,2.979 0.156,0.198 10 false 3 2.708,2.781 2.865,2.979 0.156,0.198 10 false 6 2.271,2.865 2.885,3.063 0.615,0.198 10 false TRN1 1.146,2.875 1.76,3.073 0.615,0.198 10 false TRN2 1.135,4.135 1.75,4.333 0.615,0.198 10 false TRN3 2.25,4.125 2.865,4.323 0.615,0.198 10 false TRN4 0.25,7.083 1.75,7.417 1.5,0.333 10 false *3: for TMC Made 0.25,7.417 1.667,7.75 1.417,0.333 10 false *4: for TMMT Made 0.25,6.417 1.75,6.75 1.5,0.333 10 false *1: for Bulb Type 0.25,6.75 1.667,7.083 1.417,0.333 10 false *2: for LED Type


FOR LH SIDE TURN SIGNAL LIGHT


E426559E04
2.49,0.531 2.646,0.729 0.156,0.198 10 false B 2.51,1.656 2.667,1.854 0.156,0.198 10 false B 1.125,1.656 1.281,1.854 0.156,0.198 10 false E 1.135,0.531 1.292,0.729 0.156,0.198 10 false E 2.771,5.073 2.927,5.271 0.156,0.198 10 false B 2.781,5.5 2.938,5.698 0.156,0.198 10 false - 0.417,3.917 2.917,4.271 2.5,0.354 10 false Side Turn Signal Light Assembly LH*3 5.26,2.771 5.833,3.417 0.573,0.646 10 false Flasher Relay IC 6.229,3.635 6.688,3.833 0.458,0.198 10 false CPU 5.906,0.906 6.615,1.219 0.708,0.313 10 false Turn LH 4.906,6.594 5.219,6.792 0.313,0.198 10 false F5 4.896,6.771 6.875,7.25 1.979,0.479 10 false Combination Meter Assembly 4.615,0.531 4.927,0.729 0.313,0.198 10 false LL 0.469,4.302 0.781,4.5 0.313,0.198 10 false J7 0.448,4.469 3.104,4.813 2.656,0.344 10 false Outer Rear View Mirror Assembly LH*3 3.167,0.542 3.479,0.74 0.313,0.198 10 false *1 3.167,1.646 3.479,1.844 0.313,0.198 10 false *2 2.969,5.073 3.313,5.344 0.344,0.271 10 false 16 2.979,5.521 3.281,5.813 0.302,0.292 10 false 12 2.719,1.656 2.875,1.854 0.156,0.198 10 false 2 2.698,0.531 2.854,0.729 0.156,0.198 10 false 2 0.948,0.531 1.104,0.729 0.156,0.198 10 false 6 0.927,1.656 1.083,1.854 0.156,0.198 10 false 6 4.354,0.552 4.625,0.74 0.271,0.188 10 false 13 1.135,1 1.594,1.198 0.458,0.198 10 false A88 1.125,2.115 1.583,2.313 0.458,0.198 10 false A88 1.125,1.167 2.813,1.531 1.688,0.365 10 false Headlight Assembly LH*1 1.115,2.281 2.802,2.646 1.688,0.365 10 false Headlight Assembly LH*2 0.25,7.083 2.25,7.417 2,0.333 10 false *1: for Triple Beam Headlight 0.25,7.417 2.635,7.75 2.385,0.333 10 false *2: for Single Beam Headlight 2.979,3.083 3.135,3.281 0.156,0.198 10 false 1 2.979,3.542 3.135,3.74 0.156,0.198 10 false 2 2.75,3.083 2.906,3.281 0.156,0.198 10 false B 2.76,3.542 2.917,3.74 0.156,0.198 10 false E 0.427,5.99 2.927,6.344 2.5,0.354 10 false Side Turn Signal Light Assembly LH*4 0.49,6.667 3.146,7.01 2.656,0.344 10 false Outer Rear View Mirror Assembly LH*4 0.51,6.479 0.896,6.708 0.385,0.229 10 false J11 3.385,3.094 3.698,3.292 0.313,0.198 10 false *3 3.844,3.563 4.156,3.76 0.313,0.198 10 false *4 2.5,7.083 4.5,7.417 2,0.333 10 false *3: for TMMT Made 2.5,7.417 4.885,7.75 2.385,0.333 10 false *4: for TMC Made

E426529E04
2.302,1.021 2.646,1.26 0.344,0.24 10 false TRN 1.135,1.021 1.292,1.219 0.156,0.198 10 false E 2.5,4.552 2.656,4.75 0.156,0.198 10 false B 1.135,4.552 1.292,4.75 0.156,0.198 10 false E 5.25,3.26 5.823,3.906 0.573,0.646 10 false Flasher Relay IC 6.229,4.167 6.688,4.365 0.458,0.198 10 false CPU 4.906,6.594 5.219,6.792 0.313,0.198 10 false F5 4.896,6.771 6.875,7.25 1.979,0.479 10 false Combination Meter Assembly 4.615,1.01 5.313,1.229 0.698,0.219 10 false TRNL 3.167,1.021 3.479,1.219 0.313,0.198 10 false *1 3.854,1.75 4.167,1.948 0.313,0.198 10 false *2 2.698,4.448 2.854,4.646 0.156,0.198 10 false 1 0.958,4.448 1.115,4.646 0.156,0.198 10 false 2 2.708,2.365 2.865,2.563 0.156,0.198 10 false 5 2.698,1.021 2.854,1.219 0.156,0.198 10 false 4 0.948,1.021 1.104,1.219 0.156,0.198 10 false 3 0.938,2.365 1.094,2.563 0.156,0.198 10 false 4 4.427,1.01 4.583,1.208 0.156,0.198 10 false 6 1.083,1.5 2.083,1.833 1,0.333 10 false M48*3, q1*4 1.135,4.885 1.594,5.083 0.458,0.198 10 false S16 1.135,5.052 3.031,5.448 1.896,0.396 10 false Rear Light Assembly LH*2 1.094,3.354 2.563,4 1.469,0.646 10 false Rear Combination Light Assembly LH*2 1.083,1.677 2.563,2.344 1.479,0.667 10 false Rear Combination Light Assembly LH*1 1.094,3.188 2.542,3.594 1.448,0.406 10 false M115*3, q2*4 2.344,2.469 2.802,2.667 0.458,0.198 10 false TRN 0.958,4.031 1.115,4.229 0.156,0.198 10 false 5 2.698,4.042 2.854,4.24 0.156,0.198 10 false 6 1.135,2.458 1.292,2.656 0.156,0.198 10 false E 0.938,2.781 1.094,2.979 0.156,0.198 10 false 3 2.708,2.781 2.865,2.979 0.156,0.198 10 false 6 2.271,2.865 2.885,3.063 0.615,0.198 10 false TRN1 1.146,2.875 1.76,3.073 0.615,0.198 10 false TRN2 1.135,4.135 1.75,4.333 0.615,0.198 10 false TRN3 2.25,4.125 2.865,4.323 0.615,0.198 10 false TRN4 0.25,7.083 1.75,7.417 1.5,0.333 10 false *3: for TMC made 0.25,7.417 1.667,7.75 1.417,0.333 10 false *4: for TMMT Made 0.25,6.417 1.75,6.75 1.5,0.333 10 false *1: for Bulb Type 0.25,6.75 1.667,7.083 1.417,0.333 10 false *2: for LED Type


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the LEDs and bulbs for this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
RH side turn signal light does not illuminate. A
LH side turn signal light does not illuminate. B



A

2.CHECK TURN SIGNAL LIGHTS (RH SIDE)

B

8.CHECK TURN SIGNAL LIGHTS (LH SIDE)
2.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the power switch on (IG).


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light assembly (RH side) does not blink. A
Side turn signal light assembly (RH side) does not blink. B
Rear turn signal light assembly (RH side) does not blink (for Bulb Type). C
Rear turn signal light assembly (RH side) does not blink (for LED Type). D



A

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)

B

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)

C

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)

D

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the A89 headlight assembly RH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A89-2 (B) - F5-7 (LR) Always Below 1 Ω
A89-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A89-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the F5 combination meter assembly connector.


b.

Disconnect the I7*1 or I8*2 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
I7-16 (B) - F5-7 (LR)*1 Always Below 1 Ω
I8-1 (B) - F5-7 (LR)*2 Always Below 1 Ω
I7-12 (E) - Body ground*1 Always Below 1 Ω
I8-2 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
I7-16 (B) - Body ground*1 Always 10 kΩ or higher
I8-1 (B) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the M47*1 or o1*2 rear combination light assembly RH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M47-4 (TRN) - F5-5 (TRNR)*1 Always Below 1 Ω
o1-4 (TRN) - F5-5 (TRNR)*2 Always Below 1 Ω
M47-3 (E) - Body ground*1 Always Below 1 Ω
o1-3 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M47-4 (TRN) - Body ground*1 Always 10 kΩ or higher
o1-4 (TRN) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the S15 rear light assembly RH connectors.


b.

Disconnect the M114*1 or o2*2 rear combination light assembly RH connector.


c.

Disconnect the F5 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Rear light assembly RH
Tester Connection Condition Specified Condition
S15-1 (B) - F5-5 (TRNR) Always Below 1 Ω
S15-2 (E) - Body ground Always Below 1 Ω

Rear combination light assembly RH
Tester Connection Condition Specified Condition
M114-5 (TRN) - F5-5 (TRNR) Always Below 1 Ω
o2-5 (TRN) - F5-5 (TRNR) Always Below 1 Ω
M114-4 (E) - Body ground Always Below 1 Ω
o2-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Rear light assembly RH
Tester Connection Condition Specified Condition
S15-1 (B) or F5-5 (TRNR) - Body ground Always 10 kΩ or higher

Rear combination light assembly RH
Tester Connection Condition Specified Condition
M114-5 (TRN) or F5-5 (TRNR) - Body ground Always 10 kΩ or higher
o2-5 (TRN) or F5-5 (TRNR) - Body ground Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY RH AND REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M114-3 (TRN2) - S15-5 (TRN3)*1 Always Below 1 Ω
o2-3 (TRN2) - S15-5 (TRN3)*2 Always Below 1 Ω
M114-3 (TRN2) or S15-5 (TRN3) - Body ground*1 Always 10 kΩ or higher
o2-3 (TRN2) or S15-5 (TRN3) - Body ground*2 Always 10 kΩ or higher
M114-6 (TRN1) - S15-6 (TRN4)*1 Always Below 1 Ω
o2-6 (TRN1) - S15-6 (TRN4)*2 Always Below 1 Ω
M114-6 (TRN1) or S15-6 (TRN4) - Body ground*1 Always 10 kΩ or higher
o2-6 (TRN1) or S15-6 (TRN4) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the power switch on (IG).


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light assembly (RH side) does not blink. A
Side turn signal light assembly (LH side) does not blink. B
Rear turn signal light assembly (LH side) does not blink (for Bulb Type). C
Rear turn signal light assembly (LH side) does not blink (for LED Type). D



A

9.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)

B

10.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)

C

11.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)

D

12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
9.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the A88 headlight assembly LH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A88-2 (B) - F5-13 (LL) Always Below 1 Ω
A88-6 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A88-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the F5 combination meter assembly connector.


b.

Disconnect the J11*1 or J7*2 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J11-16 (B) - F5-13 (LL)*1 Always Below 1 Ω
J7-1 (B) - F5-13 (LL)*2 Always Below 1 Ω
J11-12 (E) - Body ground*1 Always Below 1 Ω
J7-2 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J11-16 (B) - Body ground*1 Always 10 kΩ or higher
J7-1 (B) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the M48*1 or q1*2 rear combination light assembly LH connector.


b.

Disconnect the F5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
M48-2 (TRN) - F5-6 (TRNL)*1 Always Below 1 Ω
q1-2 (TRN) - F5-6 (TRNL)*2 Always Below 1 Ω
M48-6 (E) - Body ground*1 Always Below 1 Ω
q1-3 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
M48-2 (TRN) - Body ground*1 Always 10 kΩ or higher
q1-4 (TRN) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the S16 rear light assembly LH connectors.


b.

Disconnect the M115*1 or q2*2 rear combination light assembly LH connector.


c.

Disconnect the F5 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Rear light assembly LH
Tester Connection Condition Specified Condition
S16-1 (B) - F5-6 (TRNL) Always Below 1 Ω
S16-2 (E) - Body ground Always Below 1 Ω

Rear combination light assembly LH
Tester Connection Condition Specified Condition
M115-5 (TRN) - F5-6 (TRNL)*1 Always Below 1 Ω
q2-5 (TRN) - F5-6 (TRNL)*2 Always Below 1 Ω
M115-4 (E) - Body ground*1 Always Below 1 Ω
q2-4 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Rear light assembly LH
Tester Connection Condition Specified Condition
S16-1 (B) or F5-6 (TRNL) - Body ground Always 10 kΩ or higher

Rear combination light assembly LH
Tester Connection Condition Specified Condition
M115-5 (TRN) or F5-6 (TRNL) - Body ground*1 Always 10 kΩ or higher
q2-5 (TRN) or F5-6 (TRNL) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH AND REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M115-3 (TRN2) - S16-5 (TRN3)*1 Always Below 1 Ω
q2-3 (TRN2) - S16-5 (TRN3)*2 Always Below 1 Ω
M115-3 (TRN2) or S16-5 (TRN3) - Body ground*1 Always 10 kΩ or higher
q2-3 (TRN2) or S16-5 (TRN3) - Body ground*2 Always 10 kΩ or higher
M115-6 (TRN1) - S16-6 (TRN4)*1 Always Below 1 Ω
q2-6 (TRN1) - S16-6 (TRN4)*2 Always Below 1 Ω
M115-6 (TRN1) or S16-6 (TRN4) - Body ground*1 Always 10 kΩ or higher
q2-6 (TRN1) or S16-6 (TRN4) - Body ground*2 Always 10 kΩ or higher



*1: for TMC Made

*2: for TMMT Made


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR