The combination meter assembly communicates with the ECM, brake actuator assembly (skid control ECU), power steering ECU assembly, main body ECU (multiplex network body ECU), airbag sensor assembly, radio and display receiver assembly*1, headlight control ECU sub-assembly LH*2, forward recognition camera*3 and millimeter wave radar sensor assembly*3 via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | Note |
|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM / PCM "A" | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with ECM or hybrid vehicle control ECU continues for 2 seconds or more |
·
ECM ·
CAN communication system ·
Combination meter assembly ·
Hybrid vehicle control ECU |
DTC stored | - |
| U0129 | Lost Communication with Brake System Control Module | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with brake actuator assembly (skid control ECU) continues for 3 seconds or more |
·
Brake actuator assembly (skid control ECU) ·
CAN communication system ·
Combination meter assembly |
DTC stored | - |
| U0131 | Lost Communication with Power Steering Control Module | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with power steering ECU assembly continues for 3 seconds or more |
·
Power steering ECU assembly ·
CAN communication system ·
Combination meter assembly |
DTC stored | - |
| U0142 | Lost Communication with Body Control Module "B" | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with main body ECU (multiplex network body ECU) continues for 3 seconds or more |
·
Main body ECU (multiplex network body ECU) ·
CAN communication system ·
Combination meter assembly |
DTC stored | - |
| U0151 | Lost Communication with Restraints Control Module | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with airbag sensor assembly continues for 10 seconds or more |
·
Airbag sensor assembly ·
CAN communication system ·
Combination meter assembly |
DTC stored | - |
| U0163 | Lost Communication with Navigation Control Module | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with radio and display receiver assembly continues for 3 seconds or more |
·
Radio and display receiver assembly ·
CAN communication system ·
Combination meter assembly |
DTC stored | *1 |
| U0182 | Lost Communication with Lighting Control Module Front | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with headlight control ECU sub-assembly LH continues for 10 seconds or more |
·
Headlight control ECU sub-assembly LH ·
CAN communication system ·
Combination meter assembly |
DTC stored | *2 |
| U0235 | Lost Communication with Cruise Control Front Distance Range Sensor | When IG voltage is 9.5 V or more and the following condition is detected:
·
No communication with millimeter wave radar sensor assembly continues for 10 seconds or more |
·
Millimeter wave radar sensor assembly ·
CAN communication system ·
Combination meter assembly |
DTC stored | *3 |
| U023A | Lost Communication with Front Camera Module | When IG voltage is 9.5 V or more and either of the following conditions is met:
·
No communication with forward recognition camera continues for 10 seconds or more |
·
Forward recognition camera ·
CAN communication system ·
Combination meter assembly |
DTC stored | *3 |
*1: for Radio and Display Receiver Type
*2: w/ Headlight ECU
*3: w/ Toyota Safety Sense
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
CAN communication DTCs are not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING